IC Phoenix
 
Home ›  TT35 > TJA1049T,High-speed CAN transceiver with Standby mode
TJA1049T Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
TJA1049TNXPN/a243avaiHigh-speed CAN transceiver with Standby mode


TJA1049T ,High-speed CAN transceiver with Standby modeFeatures and benefits2.1 General Fully ISO 11898-2 and ISO 11898-5 compliant Suitable for 12 V an ..
TJA1050T ,High speed CAN transceiverINTEGRATED CIRCUITSDATA SHEETTJA1050High speed CAN transceiverPreliminary specification 1999 Sep 27F ..
TJA1051T ,High-speed CAN transceiverFeatures and benefits2.1 General„ Fully ISO 11898-2 compliant„ Suitable for 12 V and 24 V systems„ ..
TJA1053T ,Fault-tolerant CAN transceiver
TJA1053T ,Fault-tolerant CAN transceiver
TJA1053T ,Fault-tolerant CAN transceiver
TLP185 ,Photocoupler (phototransistor output)Absolute Maximum Ratings (Ta = 25°C) Characteristic Symbol Rating Unit Forward current I 50 mA F ..
TLP190B ,Photocoupler GaAlAs Ired & PhotoPin Configuration (top view) Forward current I 50 mA F1 6 Forward current ∆I / °C 0.5 mA / °CFdera ..
TLP191B ,Photocoupler GaAlAs Ired & PhotoTLP191B TOSHIBA Photocoupler GaAℓAs Ired & Photo-Diode Array TENTATIVE TLP191B Telecommunicatio ..
TLP191B ,Photocoupler GaAlAs Ired & PhotoPin Configuration(top view)LED Pulse forward current I 1 A FP(100µs pulse, 100 pps)1 6Reverse volta ..
TLP191B ,Photocoupler GaAlAs Ired & PhotoElectrical Characteristics (Ta = 25°C) Characteristic Symbol Test Condition Min. Typ. Max.UnitForwa ..
TLP192G. ,Photocoupler PhotorelayTLP192G TOSHIBA Photocoupler Photorelay TLP192G PC Card Modems Unit: mmPBX STB (Set Top Boxes ..


TJA1049T
High-speed CAN transceiver with Standby mode
1. General description
The TJA1049 high-speed CAN transceiver provides an interface between a Controller
Area Network (CAN) protocol controller and the physical two-wire CAN bus. The
transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in the automotive
industry, supplying the differential transmit and receive capability to (a microcontroller
with) a CAN protocol controller.
The TJA1049 belongs to the third generation of high-speed CAN transceivers from NXP
Semiconductors, offering significant improvements over first- and second-generation
devices such as the TJA1040. It offers improved ElectroMagnetic Compatibility (EMC)
and ElectroStatic Discharge (ESD) performance, and also features: Ideal passive behavior to the CAN bus when the supply voltage is off A very low-current Standby mode with bus wake-up capability TJA1049T/3 and TJA1049TK/3 can be interfaced directly to microcontrollers with
supply voltages from 3Vto5V
These features make the TJA1049 an excellent choice for all types of HS-CAN networks,
in nodes that require a low-power mode with wake-up capability via the CAN bus.
2. Features and benefits
2.1 General
Fully ISO 11898-2 and ISO 11898-5 compliant Suitable for 12 V and 24 V systems Low ElectroMagnetic Emission (EME) and high ElectroMagnetic Immunity (EMI) VIO input on TJA1049T/3 and TJA1049TK/3 allows for direct interfacing with 3Vto5V
microcontrollers SPLIT voltage output on TJA1049T and TJA1049TK for stabilizing recessive bus level Both variants available in SO8 and HVSON8 packages Leadless HVSON8 package (3.0 mm 3.0 mm) with improved Automated Optical
Inspection (AOI) capability Dark green product (halogen free and Restriction of Hazardous Substances (RoHS)
compliant)
2.2 Low-power management
Very low-current Standby mode with host and bus wake-up capability Functional behavior predictable under all supply conditions Transceiver disengages from the bus when not powered up (zero load)
TJA1049
High-speed CAN transceiver with Standby mode
Rev. 3 — 16 September 2013 Product data sheet
NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode
2.3 Protection
High ESD handling capability on the bus pins Bus pins protected against transients in automotive environments Transmit Data (TXD) dominant time-out function Bus-dominant time-out function in Standby mode Undervoltage detection on pins VCC and VIO Thermally protected
3. Quick reference data

4. Ordering information

[1] TJA1049T and TJA1049TK with SPLIT pin; TJA1049T/3 and TJA1049TK/3 with VIO pin.
Table 1. Quick reference data

VCC supply voltage 4.75 - 5.25 V
ICC supply current Standby mode: TJA1049T, TJA1049TK - 10 15 A
Standby mode: TJA1049T/3, TJA1049TK/3 - - 5 A
Normal mode; bus recessive 2.5 5 7.5 mA
Normal mode; bus dominant 20 45 65 mA
Vuvd(VCC) undervoltage detection voltage
on pin VCC
3.5 - 4.75 V
VIO supply voltage on pin VIO 2.8 - 5.5 V
IIO supply current on pin VIO Standby mode 5 - 14 A
Normal mode; bus recessive 15 80 200 A
Normal mode; bus dominant - 350 1000 A
Vuvd(VIO) undervoltage detection voltage
on pin VIO
1.3 2.0 2.7 V
VESD electrostatic discharge voltage IEC 61000-4-2 at pins CANH and CANL 8- +8 kV
VCANH voltage on pin CANH no time limit; DC limiting value 58 - +58 V
VCANL voltage on pin CANL no time limit; DC limiting value 58 - +58 V
VSPLIT voltage on pin SPLIT no time limit; DC limiting value 58 - +58 V
Tvj virtual junction temperature 40 - +150 C
Table 2. Ordering information

TJA1049T SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1
TJA1049TK HVSON8 plastic thermal enhanced very thin small outline package; no leads; terminals; body 3 3 0.85 mm
SOT782-1
TJA1049T/3 SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1
TJA1049TK/3 HVSON8 plastic thermal enhanced very thin small outline package; no leads; terminals; body 3 3 0.85 mm
SOT782-1
NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode
5. Block diagram

NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode
6. Pinning information
6.1 Pinning

6.2 Pin description

[1] For enhanced thermal and electrical performance, the exposed center pad of the HVSON8 package should
be soldered to board ground (and not to any other voltage level).
Table 3. Pin description

TXD 1 transmit data input
GND 2[1] ground supply
VCC 3 supply voltage
RXD 4 receive data output; reads out data from the bus lines
SPLIT 5 common-mode stabilization output; TJA1049T and TJA1049TK only
VIO 5 supply voltage for I/O level adapter; TJA1049T/3 and TJA1049TK/3 only
CANL 6 LOW-level CAN bus line
CANH 7 HIGH-level CAN bus line
STB 8 Standby mode control input
NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode
7. Functional description

The TJA1049 is a HS-CAN stand-alone transceiver with Standby mode. It combines the
functionality of the PCA82C250, PCA82C251 and TJA1040 transceivers with improved
EMC and ESD handling capability and quiescent current performance. Improved slope
control and high DC handling capability on the bus pins provide additional application
flexibility.
The TJA1049 is available in two versions, distinguished only by the function of pin 5: The TJA1049T and TJA1049TK are 100 % backwards compatible with the TJA1040
when operating with a 5 V microcontroller, and also cover existing PCA82C250 and
PCA82C251 applications The TJA1049T/3 and TJA1049TK/3 allow for direct interfacing to microcontrollers with
supply voltages down to 3V
7.1 Operating modes

The TJA1049 supports two operating modes, Normal and Standby, which are selectable
via pin STB. See Table 4 for a description of the operating modes under normal supply
conditions.
7.1.1 Normal mode

A LOW level on pin STB selects Normal mode. In this mode, the transceiver can transmit
and receive data via the bus lines CANH and CANL (see Figure 1 for the block diagram).
The differential receiver converts the analog data on the bus lines into digital data which is
output on pin RXD. The slope of the output signals on the bus lines is controlled and
optimized in a way that guarantees the lowest possible EME.
7.1.2 Standby mode

A HIGH level on pin STB selects Standby mode. In Standby mode, the transceiver is not
able to transmit or correctly receive data via the bus lines. The transmitter and
Normal-mode receiver blocks are switched off to reduce supply current, and only a
low-power differential receiver monitors the bus lines for activity. The wake-up filter on the
output of the low-power receiver does not latch bus dominant states, but ensures that only
bus dominant and bus recessive states that persist longer than tfltr(wake)bus are reflected on
pin RXD.
In Standby mode, the bus lines are biased to ground to minimize the system supply
current. The low-power receiver is supplied by VIO, and is capable of detecting CAN bus
activity even if VIO is the only supply voltage available. When pin RXD goes LOW to signal
a wake-up request, a transition to Normal mode will not be triggered until STB is forced
LOW.
Table 4. Operating modes

Normal LOW bus dominant bus recessive
Standby HIGH wake-up request
detected
no wake-up request
detected
NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode
7.2 Fail-safe features
7.2.1 TXD dominant time-out function

A ‘TXD dominant time-out’ timer is started when pin TXD is set LOW. If the LOW state on
pin TXD persists for longer than tto(dom)TXD, the transmitter is disabled, releasing the bus
lines to recessive state. This function prevents a hardware and/or software application
failure from driving the bus lines to a permanent dominant state (blocking all network
communications). The TXD dominant time-out timer is reset when pin TXD is set HIGH.
The TXD dominant time-out time also defines the minimum possible bit rate of 40 kbit/s.
7.2.2 Bus dominant time-out function

In Standby mode, a 'bus dominant time-out' timer is started when the CAN bus changes
from recessive to dominant state. If the dominant state on the bus persists for longer than
tto(dom)bus, the RXD pin is forced HIGH. This prevents a clamped dominant bus (due to a
bus short-circuit or a failure in one of the other nodes on the network) generating a
permanent wake-up request. The bus dominant time-out timer is reset when the CAN bus
changes from dominant to recessive state.
7.2.3 Internal biasing of TXD and STB input pins

Pins TXD and STB have internal pull-ups to VIO to ensure a safe, defined state in case
one (or both) of these pins is left floating. Pull-up currents flow in these pins in all states;
both pins should be held HIGH in Standby mode to minimize standby current.
7.2.4 Undervoltage detection on pins VCC and VIO

Should VCC drop below the VCC undervoltage detection level, Vuvd(VCC), the transceiver
will switch to Standby mode. The logic state of pin STB will be ignored until VCC has
recovered.
Should VIO drop below the VIO undervoltage detection level, Vuvd(VIO), the transceiver will
switch off and disengage from the bus (zero load) until VIO has recovered.
7.2.5 Overtemperature protection

The output drivers are protected against overtemperature conditions. If the virtual junction
temperature exceeds the shutdown junction temperature, Tj(sd), the output drivers will be
disabled until the virtual junction temperature falls below Tj(sd) and TXD becomes
recessive again. Including the TXD condition ensures that output driver oscillation due to
temperature drift is avoided.
7.3 SPLIT output pin and VIO supply pin

Two versions of the TJA1049 are available, only differing in the function of a single pin.
Pin 5 is either a SPLIT output pin or a VIO supply pin.
7.3.1 SPLIT pin

Using the SPLIT pin on the TJA1049T or TJA1049TK in conjunction with a split
termination network (see Figure 3 and Figure 6) can help to stabilize the recessive voltage
level on the bus. This will reduce EME in networks with DC leakage to ground (e.g. from
deactivated nodes with poor bus leakage performance). In Normal mode, pin SPLIT
delivers a DC output voltage of 0.5VCC. In Standby mode or when VCC is off, pin SPLIT is
floating.
NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode

7.3.2 VIO supply pin

Pin VIO on the TJA1049T/3 and TJA1049TK/3 should be connected to the microcontroller
supply voltage (see Figure 7). This will adjust the signal levels of pins TXD, RXD and STB
to the I/O levels of the microcontroller. Pin VIO also provides the internal supply voltage for
the low-power differential receiver of the transceiver. For applications running in
low-power mode, this allows the bus lines to be monitored for activity even if there is no
supply voltage on pin VCC.
For versions of the TJA1049 without a VIO pin, the VIO input is internally connected to VCC.
This sets the signal levels of pins TXD, RXD and STB to levels compatible with 5V
microcontrollers.
NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode
8. Limiting values

[1] Verified by an external test house to ensure pins CANH and CANL can withstand ISO 7637 part 3 automotive transient test pulses 1, 2a,
3a and 3b.
[2] IEC 61000-4-2 (150 pF, 330 ); direct coupling.
[3] ESD performance of pins CANH and CANL according to IEC 61000-4-2 (150 pF, 330 ) has been be verified by an external test house.
The result is equal to or better than 8 kV (unaided).
[4] Human Body Model (HBM): according to AEC-Q100-002 (100 pF, 1.5 k).
[5] Machine Model (MM): according to AEC-Q100-003 (200 pF, 0.75 H, 10 ).
[6] Charged Device Model (CDM): according to AEC-Q100-011 (field Induced charge; 4 pF); grade C3B.
[7] In accordance with IEC 60747-1. An alternative definition of virtual junction temperature is: Tvj =Tamb+P Rth(vj-a), where Rth(vj-a) is a
fixed value to be used for the calculation of Tvj. The rating for Tvj limits the allowable combinations of power dissipation (P) and ambient
temperature (Tamb).
9. Thermal characteristics

Table 5. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are referenced to GND. voltage on pin x no time limit; DC value
on pins CANH, CANL and SPLIT 58 +58 V
on any other pin 0.3 +7 V
Vtrt transient voltage on pins CANH and CANL [1] 150 +100 V
VESD electrostatic discharge voltage IEC 61000-4-2 [2]
at pins CANH and CANL [3] 8+8 kV
HBM [4]
at pins CANH and CANL 8+8 kV
at any other pin 4+4 kV [5]
at any pin 300 +300 V
CDM [6]
at corner pins 750 +750 V
at any pin 500 +500 V
Tvj virtual junction temperature [7] 40 +150 C
Tstg storage temperature 55 +150 C
Table 6. Thermal characteristics

According to IEC 60747-1.
Rth(j-a) thermal resistance from junction to ambient SO8 package; in freeair 145 K/W
HVSON8 package; in free air 50 K/W
NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode
10. Static characteristics
Table 7. Static characteristics
Tvj= 40 C to +150 C; VCC= 4.75 V to 5.25 V; VIO= 2.8 V to 5.5V[1] =60  unless specified otherwise; All voltages are
defined with respect to ground. Positive currents flow into the IC.[2]
Supply; pin VCC

VCC supply voltage 4.75 - 5.25 V
ICC supply current Standby mode
TJA1049T or TJA1049TK;
includes IIO; VTXD =VIO
-10 15 A
TJA1049T/3 or TJA1049TK/3 - - 5 A
Normal mode
recessive; VTXD =VIO 2.5 5 7.5 mA
dominant; VTXD =0V 20 45 65 mA
Vuvd(VCC) undervoltage detection
voltage on pin VCC
3.5 - 4.75 V
I/O level adapter supply; pin VIO[1]

VIO supply voltage on pin VIO 2.8 - 5.5 V
IIO supply current on pin VIO Standby mode; VTXD =VIO 5- 14 A
Normal mode
recessive; VTXD =VIO 15 80 200 A
dominant; VTXD=0V - 350 1000 A
Vuvd(VIO) undervoltage detection
voltage on pin VIO
1.3 2.0 2.7 V
Standby mode control input; pin STB

VIH HIGH-level input voltage [3] 0.7VIO -VIO +
VIL LOW-level input voltage 0.3 - 0.3VIO V
IIH HIGH-level input current VSTB =VIO 1- +1 A
IIL LOW-level input current VSTB =0V 15 - 1 A
CAN transmit data input; pin TXD

VIH HIGH-level input voltage [3] 0.7VIO -VIO +
VIL LOW-level input voltage 0.3 - 0.3VIO V
IIH HIGH-level input current VTXD =VIO 5- +5 A
IIL LOW-level input current VTXD =0V 260 150 30 A input capacitance [4] -5 10 pF
CAN receive data output; pin RXD

IOH HIGH-level output current TJA1049T or TJA1049TK;
VRXD =VCC 0.4V 8 3 1mA
TJA1049T/3 or TJA1049TK/3;
VRXD =VIO 0.4V 9 3 1mA
IOL LOW-level output current VRXD= 0.4 V; bus dominant 1 - 12 mA
NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode

[1] Only TJA1049T/3 and TJA1049TK/3 have a VIO pin; in TJA1049T and TJA1049TK, the VIO input is internally connected to VCC.
[2] All parameters are guaranteed over the virtual junction temperature range by design. Factory testing uses correlated test conditions to
cover the specified temperature and power supply voltage range.
Bus lines; pins CANH and CANL

VO(dom) dominant output voltage VTXD =0V; t< tto(dom)TXD
pin CANH 2.75 3.5 4.5 V
pin CANL 0.5 1.5 2.25 V
Vdom(TX)sym transmitter dominant voltage
symmetry
Vdom(TX)sym = VCC VCANH VCANL 400 - +400 mV
VO(dif)bus bus differential output
voltage
VTXD =0V; t< tto(dom)TXD
VCC= 4.75 V to 5.25V =45to65
1.5 - 3 V
VTXD =VIO recessive; no load 50 - +50 mV
VO(rec) recessive output voltage Normal mode; VTXD =VIO; no load 2 0.5VCC 3V
Standby mode; no load 0.1 - +0.1 V
Vth(RX)dif differential receiver
threshold voltage
Vcm(CAN)= 12Vto +12V [5]
Normal mode 0.5 - 0.9 V
Standby mode [6] 0.4 - 1.15 V
Vhys(RX)dif differential receiver
hysteresis voltage
Vcm(CAN)= 12Vto +12V
Normal mode
100 - 300 mV
IO(sc)dom dominant short-circuit output
current
VTXD =0V; t< tto(dom)TXD; VCC =5 V
pin CANH; VCANH =0V 100 70 40 mA
pin CANL; VCANL=5V / 40 V 40 70 100 mA
IO(sc)rec recessive short-circuit
output current
Normal mode; VTXD =VIO
VCANH =VCANL = 27 V to +32V 5- +5 mA leakage current VCC =VIO = 0V;
VCANH =VCANL =5V 3- +3 A input resistance 9 15 28 k
Ri input resistance deviation between VCANH and VCANL 3- +3 %
Ri(dif) differential input resistance 19 30 52 k
Ci(cm) common-mode input
capacitance
[4] -- 20 pF
Ci(dif) differential input capacitance [4] -- 10 pF
Common mode stabilization output, pin SPLIT; only relevant for TJA1049T and TJA1049TK
output voltage Normal mode
ISPLIT= 500Ato +500A
0.3VCC 0.5VCC 0.7VCC V
Normal mode; RL =1 M 0.45VCC 0.5VCC 0.55VCCV leakage current Standby mode
VSPLIT= 58 V to +58V 5- +5 A
Temperature detection

Tj(sd) shutdown junction
temperature
[4] -190 - C
Table 7. Static characteristics …continued

Tvj= 40 C to +150 C; VCC= 4.75 V to 5.25 V; VIO= 2.8 V to 5.5V[1] =60  unless specified otherwise; All voltages are
defined with respect to ground. Positive currents flow into the IC.[2]
NXP Semiconductors TJA1049
High-speed CAN transceiver with Standby mode

[3] Maximum value assumes VCC VIO, the maximum value will be VCC + 0.3 V.
[4] Not tested in production; guaranteed by design.
[5] Vcm(CAN) is the common mode voltage of CANH and CANL.
[6] For TJA1049T/3 and TJA1049TK/3: values valid when VIO = 4.5 V to 5.5 V; when VIO = 2.8 V to 4.5 V, values valid when
Vcm(CAN)= 12Vto +12V.
11. Dynamic characteristics

[1] Only TJA1049T/3 and TJA1049TK/3 have a VIO pin; in the TJA1049T and TJA1049TK, the VIO input is internally connected to VCC.
[2] All parameters are guaranteed over the virtual junction temperature range by design. Factory testing uses correlated test conditions to
cover the specified temperature and power supply voltage range.
Table 8. Dynamic characteristics

Tvj= 40 C to +150 C; VCC= 4.75 V to 5.25 V; VIO= 2.8 V to 5.5V[1] =60  unless specified otherwise. All voltages are
defined with respect to ground. Positive currents flow into theIC.[2]
Transceiver timing; pins CANH, CANL, TXD and RXD; see Figure 4 and Figure5

td(TXD-busdom) delay time from TXD to bus dominant Normal mode - 65 - ns
td(TXD-busrec) delay time from TXD to bus recessive Normal mode - 90 - ns
td(busdom-RXD) delay time from bus dominant to RXD Normal mode - 60 - ns
td(busrec-RXD) delay time from bus recessive to RXD Normal mode - 65 - ns
tPD(TXD-RXD) propagation delay from TXD to RXD versions with SPLIT pin
Normal mode - 220 ns
versions with VIO pin
Normal mode - 250 ns
tto(dom)TXD TXD dominant time-out time VTXD=0 V; Normal mode 0.3 2 5 ms
tto(dom)bus bus dominant time-out time Standby mode 0.3 2 5 ms
tfltr(wake)bus bus wake-up filter time version with SPLIT pin
Standby mode
0.5 1 3 s
versions with VIO pin
Standby mode
0.5 1.5 5 s
td(stb-norm) standby to normal mode delay time 7 25 47 s
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED