THS10082IDA ,10 Bit, 8 MSPS ADC W/Dual Channel, Parallel DSP/uP Interface, 16X FIFO, Channel AutoScan, Low PowerFEATURESreference voltages for the ADC (1.5 V and 3.5 V) are Simultaneous Sampling of Two Single-E ..
THS1009IDA ,10-Bit, 8 MSPS ADC Dual Ch., Parallel DSP/uP, Channel Autoscan, Low PowerFEATURESTHS1009 consists of two analog inputs, which are Simultaneous Sampling of Two Single-Ended ..
THS1030CPW ,10-Bit, 30 MSPS ADC Single Ch., Pin Comp. w/TLC876, Out of Range Indicator, PowerDownmaximum ratings over operating free-air temperature (unless otherwise noted)Supply voltage range: A ..
THS1030CPW ,10-Bit, 30 MSPS ADC Single Ch., Pin Comp. w/TLC876, Out of Range Indicator, PowerDownmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
THS1030CPWRG4 ,10-Bit, 30 MSPS ADC Single Ch., Pin Comp. w/TLC876, Out of Range Indicator, PowerDown 28-TSSOP 0 to 70maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
THS1030IDW ,10-Bit, 30 MSPS ADC Single Ch., Pin Comp. w/TLC876, Out of Range Indicator, PowerDownmaximum ratings over operating free-air temperature (unless otherwise noted)Supply voltage range: A ..
TLC549CP ,8-Bit, 40 kSPS ADC Serial Out, Low Power, Compatible to TLC540/545/1540, Single Ch.features include versatile control logic, an on-chip sample-and-hold circuit thatcan operate automa ..
TLC549ID ,8-Bit, 40 kSPS ADC Serial Out, Low Power, Compatible to TLC540/545/1540, Single Ch.features include versatile control logic, an on-chip sample-and-hold circuit thatcan operate automa ..
TLC549IDR ,8-Bit, 40 kSPS ADC Serial Out, Low Power, Compatible to TLC540/545/1540, Single Ch. TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERSWITH SERIAL CONTROLSLAS067C – ..
TLC549IDRG4 ,8-Bit, 40 kSPS ADC Serial Out, Low Power, Compatible to TLC540/545/1540, Single Ch. 8-SOIC TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERSWITH SERIAL CONTROLSLAS067C – ..
TLC549IP ,8-Bit, 40 kSPS ADC Serial Out, Low Power, Compatible to TLC540/545/1540, Single Ch.block diagram1REF+3 8-BitREF–Analog-to8DigitalSample2Converter 8andOutputANALOG IN8-to-1 Data(Switc ..
TLC549IPS ,8-Bit, 40 kSPS ADC Serial Out, Low Power, Compatible to TLC540/545/1540, Single Ch. TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERSWITH SERIAL CONTROLSLAS067C – ..
THS10082IDA
10 Bit, 8 MSPS ADC W/Dual Channel, Parallel DSP/uP Interface, 16X FIFO, Channel AutoScan, Low Power
��������
SLAS254B − MAY 2002 − REVISED NOVEMBER 2002
������� ��� ������ ������ ������� ������������ ��������
����������������� ���������
FEATURES Simultaneous Sampling of Two Single-Ended
Signals or One Differential Signal Integrated 16-Word FIFO Signal-to-Noise and Distortion Ratio: 59 dB at
fI = 2 MHz Differential Nonlinearity Error: ±1 LSB Integral Nonlinearity Error: ±1 LSB Auto-Scan Mode for Two Inputs 3-V or 5-V Digital Interface Compatible Low Power: 216 mW Max 5-V Analog Single Supply Operation Internal Voltage References ...
50 PPM/°C
and ±5% Accuracy Parallel µC/DSP Interface
APPLICATIONS Radar Applications Communications Control Applications High-Speed DSP Front-End Automotive Applications
DESCRIPTIONThe THS10082 is a CMOS, low-power, 10-bit, 8 MSPS
analog-to-digital converter (ADC). The speed, resolution,
bandwidth, and single-supply operation are suited for
applications in radar, imaging, high-speed acquisition, and
communications. A multistage pipelined architecture with
output error correction logic provides for no missing codes
over the full operating temperature range. Internal control
registers allow for programming the ADC into the desired
mode. The THS10082 consists of two analog inputs,
which are sampled simultaneously. These inputs can be
selected individually and configured to single-ended or
differential inputs. An integrated 16 word deep FIFO
allows the storage of data in order to take the load off
of the processor connected to the ADC. Internal
reference voltages for the ADC (1.5 V and 3.5 V) are
provided.
An external reference can also be chosen to suit the dc
accuracy and temperature drift requirements of the
application. Two different conversion modes can be
selected. In the single conversion mode, a single and
simultaneous conversion can be initiated by using the
single conversion start signal (CONVST). The conversion
clock in the single conversion mode is generated internally
using a clock oscillator circuit. In the continuous
conversion mode, an external clock signal is applied to the
CONV_CLK input of the THS10082. The internal clock
oscillator is switched off in the continuous conversion
mode.
The THS10082C is characterized for operation from 0°C
to 70°C, and the THS10082I is characterized for operation
from −40°C to 85°C.
www.ti.com
