TDA7498 ,100W+100W dual BTL Class-D audio amplifierApplications circuit for 6- or 8-Ω speakers . . . . . 19Figure 20. Standby and mute circuits ..
TDA7498 ,100W+100W dual BTL Class-D audio amplifierblock diagram (showing one channel only) . . . . . . . 5Figure 2. Pin connections (top view, PCB ..
TDA7498L ,80 W + 80 W dual BTL class-D audio amplifierblock diagram (showing one channel only) . . . . . . . 5Figure 2. Pin connections (top view, PCB ..
TDA7499 ,6 + 6W STEREO AMPLIFIER WITH MUTE & ST-BYELECTRICAL CHARACTERISTICS (Refer to the test circuit, V = + 14V; RS = 50Ω;SG = 30dB; f = 1KHz; T = ..
TDA7499SA ,6W+6W STEREO AMPLIFIER WITH MUTE & ST-BYFEATURES Figure 1. Package■ WIDE SUPPLY VOLTAGE RANGE UP TO +18V■ 6+6W @THD = 10%, R = 8Ω , V = ±10 ..
TDA7500 ,DIGITAL AM/FM SIGNAL PROCESSORBLOCK DIAGRAManalog inanalog audio outSC SC SC SC SC SCΣΔ ΣΔ ΣΔ ΣΔFilter Filter Filter Filter Filte ..
THS4031CD ,100-MHz Low Noise Voltage-Feedback AmplifierFeatures 3 DescriptionThe THS4031 and THS4032 are ultra-low voltage1• Ultra-Low 1.6 nV/√Hz Voltage ..
THS4031CDG4 ,100-MHz Low Noise Voltage-Feedback Amplifier 8-SOIC 0 to 70Block Diagrams. 20Information..... 339.3 Feature Description.... 214 Revision HistoryNOTE: Page num ..
THS4031CDGN ,100-MHz Low Noise Voltage-Feedback Amplifier.(2) The D and DGN packages are available taped and reeled. Add an R suffix to the device type (tha ..
THS4031CDR ,100-MHz Low Noise Voltage-Feedback Amplifier SLOS224H–JULY 1999–REVISED JUNE 20165 Device Comparison Table(1)Table 1. Available OptionsPACKAGED ..
THS4031IDG4 ,100-MHz Low Noise Voltage-Feedback Amplifier 8-SOIC -40 to 85Electrical Characteristics – R = 1 kΩ..... 8L13.5 Community Resources...... 327.8 Typical Character ..
THS4031IDGN ,100-MHz Low Noise Voltage-Feedback AmplifierMaximum Ratings . 512.3 General PowerPAD™ Design Considerations...... 297.2 ESD Ratings........ 513 ..
TDA7498
100W+100W dual BTL Class-D audio amplifier
September 2011 Doc ID 16107 Rev 8 1/28
TDA7498100-watt + 100-watt dual BTL class-D audio amplifier
Features 100-W + 100-W output power at
THD = 10% with RL = 6 Ω and VCC = 36 V 80-W + 80-W output power at
THD = 10% with RL = 8 Ω and VCC = 34 V Wide-range single-supply operation (14 - 39 V) High efficiency (η = 90%) Four selectable, fixed gain settings of
nominally 25.6 dB, 31.6 dB, 35.1 dB and
37.6 dB Differential inputs minimize common-mode
noise Standby and mute features Short-circuit protection Thermal overload protection Externally synchronizable
DescriptionThe TDA7498 is a dual BTL class-D audio
amplifier with single power supply designed for
home systems and active speaker applications.
It comes in a 36-pin PowerSSO package with
exposed pad up (EPU) to facilitate mounting a
separate heatsink.
Table 1. Device summary
Contents TDA74982/28 Doc ID 16107 Rev 8
Contents Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Pin list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Characterizations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113.1 T est circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 Characterization curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2.1 For RL = 6 Ω . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.2.2 For RL = 8 Ω . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Applications information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194.1 Applications circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.2 Mode selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.3 Gain setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.4 Input resistance and capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.5 Internal and external clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.5.1 Master mode (internal clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.5.2 Slave mode (external clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.6 Output low-pass filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.7 Protection functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.8 Diagnostic output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
TDA7498 List of figures
Doc ID 16107 Rev 8 3/28
List of figures
Figure 1. Internal block diagram (showing one channel only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 2. Pin connections (top view, PCB view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 3. Test circuit for characterizations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 4. Test board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 5. Output power (THD = 10%) vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 6. THD vs. output power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 7. THD vs. frequency (1 W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 8. THD vs. frequency (100 mW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 9. Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 10. FFT performance (0 dBFS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 11. FFT performance (-60 dBFS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 12. Output power (THD = 10%) vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 13. THD vs. output power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 14. THD vs. frequency (1 W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 15. THD vs. frequency (100 mW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 16. Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 17. FFT performance (0 dB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 18. FFT performance (-60 dB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 19. Applications circuit for 6- or 8-Ω speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 20. Standby and mute circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 21. Turn on/off sequence for minimizing speaker “pop” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 22. Input circuit and frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 23. Master and slave connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 24. Typical LC filter for a 8-Ω speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 25. Typical LC filter for a 6-Ω speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 26. Behavior of pin DIAG for various protection conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 27. PowerSSO36 EPU outline drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
List of tables TDA7498
4/28 Doc ID 16107 Rev 8
List of tables
Table 1. Device summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 2. Pin description list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 3. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 4. Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 5. Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 6. Electrical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 7. Mode settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 8. Gain settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 9. How to set up SYNCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 10. PowerSSO36 EPU dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 11. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
TDA7498 Device block diagram
Doc ID 16107 Rev 8 5/28
Device block diagram
Figure 1 shows the block diagram of one of the two identical channels of the TDA7498.
Figure 1. Internal block diagram (showing one channel only)
Pin description TDA7498
6/28 Doc ID 16107 Rev 8
1 Pin description
1.1 Pinout
Figure 2. Pin connections (top view, PCB view)
TDA7498 Pin description
Doc ID 16107 Rev 8 7/28
1.2 Pin list
Table 2. Pin description list
Electrical specifications TDA7498
8/28 Doc ID 16107 Rev 8
2 Electrical specifications
2.1 Absolute maximum ratings
2.2 Thermal data
2.3 Recommended operating conditions
2.4 Electrical specifications
Unless otherwise stated, the values in the table below are specified for the conditions:
VCC =36V , RL = 6 Ω, ROSC = R3 = 39 kΩ, C8 = 100 nF, f = 1 kHz, GV = 25.6 dB
Tamb=25 °C.
Table 3. Absolute maximum ratings
Table 4. Thermal data
Table 5. Recommended operating conditions
Table 6. Electrical specifications
TDA7498 Electrical specifications
Doc ID 16107 Rev 8 9/28
Table 6. Electrical specifications (continued)
Electrical specifications TDA7498
10/28 Doc ID 16107 Rev 8 fSW = 106 / ((16 * ROSC + 182) * 4) kHz, fSYNCLK = 2 * fSW with R3 = 39 kΩ (see Figure 19.). fSW = fSYNCLK / 2 with the external oscillator.
Table 6. Electrical specifications (continued)
TDA7498 Characterizations
Doc ID 16107 Rev 8 11/28
3 Characterizations 3.1 T
st
cir
gur
s t
st
cir
uit
with
which
e cha
act
izat
ion
cur
, sho
n in
he
sectio
me
asur
Figu
sh
the PC
B la
ut.
re 3.
ci
t f
r c
act
izat
ions
Characterizations TDA7498
12/28 Doc ID 16107 Rev 8
Figure 4. Test board
TDA7498 Characterizations
Doc ID 16107 Rev 8 13/28
3.2 Characterization curves
Unless otherwise stated the measurements were made under the following conditions:
VCC = 36 V , f = 1 kHz, GV = 25.6 dB, ROSC = 39 kΩ, COSC = 100 nF , Tamb = 25 °C
3.2.1 For RL = 6 Ω
Figure 5. Output power (THD = 10%) vs. supply voltage
Figure 6. THD vs. output power
Characterizations TDA7498
14/28 Doc ID 16107 Rev 8
Figure 7. THD vs. frequency (1 W)
Figure 8. THD vs. frequency (100 mW)
Figure 9. Frequency response
