TDA1517P ,2 x 6 W stereo power amplifierBLOCK DIAGRAMhandbook, full pagewidthnon-inverting1mute switchCminput 160kΩ4output 1VA2kΩpower stag ..
TDA1519 ,2 x 6 W stereo car radio power amplifierINTEGRATED CIRCUITSDATA SHEETTDA15192 x 6 W stereo car radio poweramplifierMay 1992Product specifica ..
TDA1519/N2 ,TDA1519; 2 x 6 W stereo car radio power amplifier
TDA1519CTD/N3 ,TDA1519C; 22 W BTL or 2 x 11 W stereo power amplifier
TDA1519CTD/N3 ,TDA1519C; 22 W BTL or 2 x 11 W stereo power amplifier
TDA1519CTH ,22WBTL or 2 x 11Wstereo power amplifier
TEA6101T/N2 ,TEA6101/T; Antenna diversity circuit
TEA6300 ,Sound fader control circuit
TEA6300T ,Sound fader control circuit
TEA6320T ,Sound fader control circuitapplications.2• Fast mute control via I C-bus• Fast mute control via pin2• I C-bus control for all ..
TEA6321T ,Sound fader control circuit
TEA6321T ,Sound fader control circuit
TDA1517P
2 x 6 W stereo power amplifier
NXP Semiconductors Product specification
2 x 6 W stereo power amplifier TDA1517; TDA1517P
FEATURES Requires very few external components High output power Fixed gain Good ripple rejection Mute/standby switch AC and DC short-circuit safe to ground and VP Thermally protected Reverse polarity safe Capability to handle high energy on outputs (VP =0V) No switch-on/switch-off plop Electrostatic discharge protection.
GENERAL DESCRIPTIONThe TDA1517 is an integrated class-B dual output
amplifier in a plastic single in-line medium power package
with fin (SIL9MPF), a plastic rectangular-bent single in-line
medium power package with fin (RBS9MPF) or a plastic
heat-dissipating dual in-line package (HDIP18). The
device is primarily developed for multi-media applications.
QUICK REFERENCE DATA
ORDERING INFORMATION
NXP Semiconductors Product specification
2 x 6 W stereo power amplifier TDA1517; TDA1517P
BLOCK DIAGRAM
NXP Semiconductors Product specification
2 x 6 W stereo power amplifier TDA1517; TDA1517P
PINNING
FUNCTIONAL DESCRIPTIONThe TDA1517 contains two identical amplifiers with
differential input stages. The gain of each amplifier is fixed
at 20 dB. A special feature of the device is the
mute/standby switch which has the following features: Low standby current (<100 μA) Low mute/standby switching current
(low cost supply switch) Mute condition.
NXP Semiconductors Product specification
2 x 6 W stereo power amplifier TDA1517; TDA1517P
LIMITING VALUESIn accordance with the Absolute Maximum Rating System (IEC 60134).
THERMAL RESISTANCE
NXP Semiconductors Product specification
2 x 6 W stereo power amplifier TDA1517; TDA1517P
CHARACTERISTICS =14.4V; Tamb =25 °C; measured in Fig.6; unless otherwise specified.
Note The circuit is DC adjusted at VP=6to18 V and AC operating at VP= 8.5to18V.
NXP Semiconductors Product specification
2 x 6 W stereo power amplifier TDA1517; TDA1517P
CHARACTERISTICS =14.4V; RL =4 Ω; f=1 kHz; Tamb =25 °C; measured in Fig.6; unless otherwise specified.
Notes Output power is measured directly at the output pins of the IC. Frequency response externally fixed. Ripple rejection measured at the output with a source impedance of 0 Ω, maximum ripple amplitude of 2V (p-p) and
a frequency between 100 Hz and 10 kHz. Noise voltage measured in a bandwidth of 20Hzto20 kHz. Noise output voltage independent of Rs (VI =0V).
NXP Semiconductors Product specification
2 x 6 W stereo power amplifier TDA1517; TDA1517P
APPLICATION INFORMATION
