IC Phoenix
 
Home ›  MM100 > MC10H166FN-MC10H166L-MC10H166P,5-Bit Magnitude Comparator
MC10H166FN-MC10H166L-MC10H166P Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
MC10H166FNMOTON/a2266avai5-Bit Magnitude Comparator
MC10H166FNMOTN/a107avai5-Bit Magnitude Comparator
MC10H166LMOTN/a46avai5-Bit Magnitude Comparator
MC10H166PMOTON/a100avai5-Bit Magnitude Comparator


MC10H166FN ,5-Bit Magnitude ComparatorELECTRICAL CHARACTERISTICS (V = –5.2 V ±5%) (See Note)EE DIP0° 25° 75° PIN ASSIGNMENTCharacteristic ..
MC10H166FN ,5-Bit Magnitude Comparator
MC10H166FN ,5-Bit Magnitude ComparatorMAXIMUM RATINGSTRUTH TABLECharacteristic Symbol Rating UnitInputs OutputsPower Supply (V = 0) V –8. ..
MC10H166L ,5-Bit Magnitude ComparatorMAXIMUM RATINGSTRUTH TABLECharacteristic Symbol Rating UnitInputs OutputsPower Supply (V = 0) V –8. ..
MC10H166P ,5-Bit Magnitude Comparator**SEMICONDUCTOR TECHNICAL DATA** The MC10H166 is a 5–Bit Magnitude Comparator and is a functional/ ..
MC10H171 ,Dual Binary 1-4 Decoder (Low)2AN1406/Dreduced while maintaining acceptable manufacturing design. After all the inclusion of ECL ..
MC3488AP1 ,DUAL EIA-423/EIA-232D DRIVEROrder this document by MC3488A/D** ** The MC3488A dual is single–ended line driver has been designe ..
MC34911G5AC , LIN System Basis Chip with DC Motor Pre-driver
MC34912G5AC , LIN System Basis Chip with DC Motor Pre-driver and Current Sense
MC34920EI , 2.8 ohm (Typ) Quad H-Bridge Motor Driver
MC34920FN , 2.8 ohm (Typ) Quad H-Bridge Motor Driver
MC34921AE , Configurable Motor Driver IC with Power Supplies


MC10H166FN-MC10H166L-MC10H166P
5-Bit Magnitude Comparator
SEMICONDUCTOR TECHNICAL DATA -
The MC10H166 is a 5–Bit Magnitude Comparator and is a functional/
pinout duplication of the standard MECL 10K part with 100%
improvement in propagation delay and no increase in power–supply
current.
The MC10H166 is a high–speed expandable 5–bit comparator for
comparing the magnitude of two binary words. Two outputs are provided:
AB. The A = B function can be obtained by wire–ORing these
outputs (a low level indicates A = B) or by wire–NORing the outputs (a
high level indicates A = B). A high level on the enable function forces both
outputs low. Propagation Delay, Data–to–Output, 2.0 ns Typical Power Dissipation 440 mW Typical Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range) Voltage Compensated MECL 10K–Compatible
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
AC PARAMETERS
NOTES:

Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit
board and transverse air flow greater than 500 Ifpm is maintained. Outputs are terminated through a
50–ohm resistor to –2.0 volts.
DIP
PIN ASSIGNMENT

VCC1
A>B
AVEE
VCC2
TRUTH TABLE

Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–36 of the Motorola MECL Data
Book (DL122/D).
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED