MAX4584EUB ,Serially Controlled Audio/Video SwitchesELECTRICAL CHARACTERISTICS—Single +5V Supply(V+ = +5V ±5%, T = T to T , unless otherwise noted. Typ ..
MAX4584EUB+ ,Serially Controlled Audio/Video SwitchesApplicationsPART TEMP. RANGE PIN-PACKAGECellular Phones and AccessoriesMAX4584EUB -40°C to +85°C 10 ..
MAX4585EUB ,Serially Controlled Audio/Video SwitchesApplicationsPART TEMP. RANGE PIN-PACKAGECellular Phones and AccessoriesMAX4584EUB -40°C to +85°C 10 ..
MAX4586EUB ,Serially Controlled / 4-Channel Audio/Video MultiplexersELECTRICAL CHARACTERISTICS—Single +5V Supply(V+ = +5V ±5%, T = T to T , unless otherwise noted. Typ ..
MAX4586EUB ,Serially Controlled / 4-Channel Audio/Video MultiplexersApplications Ordering InformationCellular Phones and AccessoriesPART TEMP. RANGE PIN-PACKAGEMAX4586 ..
MAX4586EUB+ ,Serially Controlled, 4-Channel Audio/Video MultiplexersApplications Ordering InformationCellular Phones and AccessoriesPART TEMP. RANGE PIN-PACKAGEMAX4586 ..
MAX8710ETG+ ,Low-Cost, Linear-Regulator LCD Panel Power SuppliesELECTRICAL CHARACTERISTICS(Circuit of Figure 1. V = V = V = 12V, V = V = 10V, V = 27V, T = 0°C to + ..
MAX8715EUA ,Low-Noise Step-Up DC-DC ConvertersApplicationsMAX1790EUA+ -40°C to +85°C 8 µMAXLCD Displays MAX8715EUA -40°C to +85°C 8 µMAXPCMCIA Ca ..
MAX8715EUA ,Low-Noise Step-Up DC-DC ConvertersApplications+ Denotes lead-free package.Hand-Held DevicesTypical Operating Circuit Pin Configuratio ..
MAX8715EUA+ ,Low-Noise Step-Up DC-DC ConvertersFeaturesThe MAX1790/MAX8715 boost converters incorporate♦ 90% Efficiencyhigh-performance (at 1.2MHz ..
MAX8715EUA+T ,Low-Noise Step-Up DC-DC ConvertersApplications+ Denotes lead-free package.Hand-Held DevicesTypical Operating Circuit Pin Configuratio ..
MAX8716ETG , Interleaved High-Efficiency, Dual Power-Supply Controllers for Notebook Computers
MAX4584EUB-MAX4585EUB
Serially Controlled Audio/Video Switches
General DescriptionThe MAX4584/MAX4585 serial-interface, programmable
switches are ideal for multimedia applications. Each
device contains one normally open (NO) single-pole/
single-throw (SPST) switch and one single-pole/double-
throw (SPDT) switch. The MAX4584/MAX4585 feature
65Ωon-resistance, 4Ωon-resistance matching
between channels, and 5Ωon-resistance flatness.
Additionally, they have off-isolation of -83dB at 20kHz
and -48dB at 10MHz, with crosstalk of -84dB at 20kHz
and -60dB at 10MHz.
The MAX4584 uses a 2-wire I2C™-compatible serial
interface; the MAX4585 uses a 3-wire SPI™/QSPI™/
MICROWIRE™-compatible interface. Both devices are
available in a 10-pin μMAX package and are specified
for the extended-industrial (-40°C to +85°C) temperature
range.
ApplicationsCellular Phones and Accessories
Private Mobile Radios (PMRs)
PC Multimedia Audio/Video Routing
Industrial Equipment
Set-Top Boxes
Video Conferencing
High-End Audio Equipment
Features+2.7V to +5.5V Single-Supply OperationSPST and SPDT Switches65Ω(max) RONwith +5V SupplyAudio Performance
-83dB Off-Isolation at 20kHz
-84dB Crosstalk at 20kHzVideo Performance
-48dB Off-Isolation at 10MHz
-60dB Crosstalk at 10MHzSerial Interface
2-Wire I2C Compatible (MAX4584)
3-Wire SPI/QSPI/MICROWIRE Compatible
(MAX4585)
MAX4584/MAX4585
Serially Controlled
Audio/Video Switches19-1521; Rev 0; 8/99
Ordering InformationI2C is a trademark of Philips Corp.
SPI/QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corp.
Pin Configuration/
Functional Diagram
MAX4584/MAX4585
Serially Controlled
Audio/Video Switches
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—Single +5VSupply(V+ = +5V ±5%, TA= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.) (Note 2)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
V+ to GND................................................................-0.3V to +6V
COM_ and NO_ _ to GND (Note 1)..............-0.3V to (V+ + 0.3V)
A, CS, SDA, DIN, SCL, and SCLK to GND...............-0.3V to +6V
Continuous Current into Any Terminal..............................±20mA
Peak Current into Any Terminal
(pulsed at 1ms, 10% duty cycle).................................±40mA
ESD per Method 3015.7.......................................................>2kV
Continuous Power Dissipation (TA= +70°C)
μMAX (derate 4.1mW/°C above +70°C).....................330mW
Operating Temperature Range...........................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10sec).............................+300°C
Note 1:Signals on NO_ _or COM_ exceeding V+ or ground are clamped by internal diodes. Limit forward-diode current to maximum
current rating.
Serially Controlled
Audio/Video Switches
MAX4584/MAX4585
ELECTRICAL CHARACTERISTICS—Single +5VSupply (continued)(V+ = +5V ±5%, TA= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.) (Note 2)
MAX4584/MAX4585
Serially Controlled
Audio/Video Switches
ELECTRICAL CHARACTERISTICS—Single +3V Supply(V+ = +3.0V ±10%, TA= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.)
MAX4584/MAX4585
Serially Controlled
Audio/Video Switches
I/O INTERFACE CHARACTERISTICS(V+ = +2.7V to +5.25V, TA= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.)
2-WIRE TIMING CHARACTERISTICS (Figures 1 and 2, V+ = +2.7V to +5.25V, fSCL= 100kHz, TA= TMINto TMAX, unless otherwise noted. Typical values are at= +25°C.)
MAX4584/MAX4585
Serially Controlled
Audio/Video Switches
3-WIRE TIMING CHARACTERISTICS (Figures 3 and 4, V+ = +2.75V to +5.25V, fOP= 2.1MHz, TA= TMINto TMAX, unless otherwise noted. Typical values are at= +25°C.)
Note 2:Algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Note 3:Guaranteed by design. Not subject to production testing.
Note 4:ΔRON= RON(MAX)- RON(MIN).
Note 5:Resistance flatness is defined as the difference between the maximum and minimum on-resistance values, as measured
over the specified analog signal range.
Note 6:Leakage parameters are 100% tested at maximum rated temperature and guaranteed by correlation at TA= +25°C.
Note 7:Off-isolation = 20 log (VCOM_ / VNO_ _), VCOM_ = output, VNO_ _ = input to off switch.
Note 8:All timing is measured from the clock’s falling edge preceding the ACK signal for 2-wire and from the rising edge of CSfor
3-wire. Turn-off time is defined at the output of the switch for a 0.5V change, tested with a 300Ωload to ground. Turn-on
time is defined at the output of the switch for a 0.5V change and measured with a 5kΩload resistor to GND. All timing is
shown with respect to 20% V+ and 70% V+, unless otherwise noted.
Note 9:Leakage testing is guaranteed by testing with a +5.25V supply.
Note 10:CB= capacitance of one bus line in pF. Tested with CB= 400pF.
Note 11:Typical values are for MAX4584 devices.
Typical Operating Characteristics(V+ = +5V, TA = +25°C, unless otherwise noted.)
