MAX4542EKA-T ,Low-Voltage / Single-Supply Dual SPST/SPDT Analog SwitchesELECTRICAL CHARACTERISTICS—Single +5V Supply(V+ = +5V ±10%, GND = 0, V = 2.4V, V = 0.8V, T = T to T ..
MAX4542ESA ,Low-Voltage / Single-Supply Dual SPST/SPDT Analog SwitchesMAX4541–MAX454419-1202; Rev 1; 1/00Low-Voltage, Single-Supply Dual SPST/SPDT Analog Switches
MAX4542EUA ,Low-Voltage / Single-Supply Dual SPST/SPDT Analog SwitchesFeaturesThe MAX4541–MAX4544 are precision, dual analog Low R : 60Ω max (33Ω typ)ONswitches design ..
MAX4542EUA+ ,Low-Voltage, Single-Supply Dual SPST/SPDT Analog SwitchesApplicationsMAX4541CSA 0°C to +70°C 8 SO —Battery-Operated Systems Test EquipmentMAX4541CPA 0°C ..
MAX4543CPA ,Low-Voltage, Single-Supply Dual SPST/SPDT Analog SwitchesGeneral Description ________
MAX4543CSA ,Low-Voltage, Single-Supply Dual SPST/SPDT Analog SwitchesMAX4541–MAX454419-1202; Rev 3; 8/02Low-Voltage, Single-Supply Dual SPST/SPDT Analog Switches
MAX861ESA+T ,50mA, Frequency-Selectable, Switched-Capacitor Voltage Convertersapplications. 600mV Voltage Drop at 50mA LoadA frequency-control (FC) pin provides three switching ..
MAX861ESA+T ,50mA, Frequency-Selectable, Switched-Capacitor Voltage Convertersapplications. 600mV Voltage Drop at 50mA LoadA frequency-control (FC) pin provides three switching ..
MAX861ESA-T ,50mA, Frequency-Selectable, Switched-Capacitor Voltage ConvertersELECTRICAL CHARACTERISTICS– — — — –(Typical Operating Circuit (Inverter), V = +5V, SHDN= V , FC = L ..
MAX861ISA ,50mA, Frequency-Selectable, Switched-Capacitor Voltage ConvertersMAX860/MAX86119-0239; Rev 1; 11/9650mA, Frequency-Selectable,Switched-Capacitor Voltage Converters_ ..
MAX861ISA ,50mA, Frequency-Selectable, Switched-Capacitor Voltage Convertersapplications where the ICL7660MAX860ISA -25°C to +85°C 8 SOand MAX660's switching frequencies are t ..
MAX861ISA+ ,50mA, Frequency-Selectable, Switched-Capacitor Voltage Convertersapplications where the ICL7660MAX860ISA -25°C to +85°C 8 SOand MAX660's switching frequencies are t ..
MAX4542CSA-MAX4542CUA-MAX4542EKA-T-MAX4542ESA-MAX4542EUA
Low-Voltage / Single-Supply Dual SPST/SPDT Analog Switches
General DescriptionThe MAX4541–MAX4544 are precision, dual analog
switches designed to operate from a single +2.7V to
+12V supply. Low power consumption (5µW) makes
these parts ideal for battery-powered equipment. These
switches offer low leakage currents (100pA max) and fast
switching speeds (tON= 150ns max, tOFF= 100ns max).
When powered from a +5V supply, the MAX4541–
MAX4544 offer 2Ωmax matching between channels, 60Ω
max on-resistance (RON), and 6Ωmax RONflatness.
These switches also offer 5pC max charge injection and
a minimum of 2000V ESD protection per Method 3015.7.
The MAX4541/MAX4542/MAX4543 are dual single-pole/
single-throw (SPST) devices and the MAX4544 is a single-
pole/double-throw (SPDT) device. The MAX4541 has two
normally open (NO) switches and the MAX4542 has two
normally closed (NC) switches. The MAX4543 has one NO
and one NC switch and can be used as an SPDT, while
the MAX4544 is an SPDT. The MAX4541/MAX4542/
MAX4543 are available in tiny SOT23-8 packages, and
the MAX4544 is available in a SOT23-6 package.
________________________Applications
____________________________FeaturesLow RON: 60Ωmax (33Ωtyp)RONMatching Between Channels: 2ΩmaxRONFlatness: 6ΩmaxGuaranteed Charge Injection: 5pC max+2.7V to +12V Single-Supply OperationLow Power Consumption: <5µWLow Leakage Current Over Temperature:
10nA max at +85°CFast Switching: tON= 35ns, tOFF= 25nsGuaranteed Break-Before-Make
(MAX4543/MAX4544 only)TTL/CMOS-Logic CompatiblePin Compatible with MAX323/MAX324/MAX325MAX4541/42/43 Available in SOT23-8
MAX4544 Available in SOT23-6
MAX4541–MAX4544
Low-Voltage, Single-Supply
Dual SPST/SPDT Analog Switches19-1202; Rev 1; 1/00
Ordering Information continued at end of data sheet.*Dice are specified at TA= +25°C.
Pin Configurations/Functional Diagrams/Truth TablesBattery-Operated Systems
Sample-and-Hold Circuits
Heads-Up Displays
Guidance and Control
Systems
Audio and Video
Switching
Military Radios
Test Equipment
Communications Systems
+3V/+5V DACs and ADCs
PBX, PABX
Cell Phones
Ultrasound
Pagers
MAX4541–MAX4544
Low-Voltage, Single-Supply
Dual SPST/SPDT Analog SwitchesVoltage Referenced to GND
V+.........................................................................-0.3V to +13V
IN_, COM_, NC_, NO_ (Note 1)..................-0.3V to (V+ + 0.3V)
Continuous Current (any terminal)....................................±10mA
Peak Current, COM_, NO_, NC_
(pulsed at 1ms, 10% duty cycle max)............................±20mA
ESD per Method 3015.7..................................................>2000V
Continuous Power Dissipation
SOT23-6 (derate 7.1mW/°C above +70°C)....................571mW
SOT23-8 (derate 5.3mW/°C above +70°C)....................421mW
µMAX (derate 4.10mW/°C above +70°C)......................330mW
Narrow SO (derate 5.88mW/°C above +70°C)..............471mW
Plastic DIP (derate 9.09mW/°C above +70°C)..............727mW
Operating Temperature Ranges
MAX454_C_ _.......................................................0°C to +70°C
MAX454_E_ _.....................................................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s).................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—Single +5V Supply(V+ = +5V ±10%, GND = 0, VINH= 2.4V, VINL= 0.8V, TA= TMINto TMAX, unless otherwise noted.) (Notes 2, 3)
Note 1:Signals on NC, NO, COM, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to maximum
current rating.
MAX4541–MAX4544
Low-Voltage, Single-Supply
Dual SPST/SPDT Analog Switches
ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued)(V+ = +5V ±10%, GND = 0, VINH= 2.4V, VINL= 0.8V, TA= TMINto TMAX, unless otherwise noted.) (Notes 2, 3)
MAX4541–MAX4544
Low-Voltage, Single-Supply
Dual SPST/SPDT Analog Switches
ELECTRICAL CHARACTERISTICS—Single +3.3V Supply(V+ = +3.0V to +3.6V, GND = 0, VINH= 2.4V, VINL= 0.8V, TA= TMINto TMAX, unless otherwise noted.) (Notes 2, 3)
Note 2:SOT-packaged parts are 100% tested at +25°C only and guaranteed by correlation at the full hot rated temperature.
Note 3:The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 4:Guaranteed by design.
Note 5:∆RON= ∆RONmax - ∆RONmin.
Note 6:Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal range.
Note 7:Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25°C.
Note 8:Off Isolation = 20log10[VCOM⁄ (VNCor VNO)], VCOM= output, VNC orVNO= input to off switch.
Note 9:Between the two switches, MAX4541/MAX4542/MAX4543 only.
MAX4541–MAX4544
Low-Voltage, Single-Supply
Dual SPST/SPDT Analog SwitchesON-RESISTANCE vs. COM VOLTAGE
MAX4541-01
VCOM (V)12345
ON-RESISTANCE vs.
COM VOLTAGE OVER TEMPERATUREMAX4541-02
VCOM (V)
TURN-ON/OFF TIMES vs.
SUPPLY VOLTAGE
MAX4541-03
VSUPPLY (V)
tON
OFF
(ns)
TURN-ON/OFF TIMES
vs. TEMPERATURE
MAX4541-04
TEMPERATURE (°C)
tON
OFF
(ns)
FREQUENCY RESPONSE
MAX4541-07
FREQUENCY (MHz)
LOSS (dB)
PHASE (DEGREES)
ON/OFF-LEAKAGE CURRENT
vs. TEMPERATURE
MAX4541-05
TEMPERATURE (°C)
ON/OFF-LEAKAGE (nA)
CHARGE INJECTION vs. COM VOLTAGE
MAX4541-06
VCOM (V)
Q (pC)
INPUT VOLTAGE vs. SUPPLY CURRENT
MAX4541-08
VIN (V)
I+ (nA)12345
1001k10k
TOTAL HARMONIC DISTORTION
vs. FREQUENCYMAX4541-09
FREQUENCY (Hz)
THD (%)
__________________________________________Typical Operating Characteristics(TA = +25°C, unless otherwise noted.)
MAX4541–MAX4544
Low-Voltage, Single-Supply
Dual SPST/SPDT Analog Switches
Applications Information
Logic LevelsThe MAX4541–MAX4544 are TTL compatible when
powered from a single +5V supply. When powered
from other supply voltages, TTL compatibility is guar-
anteed and the logic inputs can be driven Rail-to-Rail®.
For example, with a +12V supply, IN1 and IN2 can be
driven low to 0 and high to 12V. With a +3.3V supply,
IN1 and IN2 should be driven low to 0 and high to
3.3V.
Driving IN1 and IN2 rail-to-rail minimizes power con-
sumption.
Analog Signal LevelsAnalog signals that range over the entire supply voltage
(V+ to GND) can be switched with very little change in
on-resistance over the entire voltage range (see Typical
Operating Characteristics). All the switches are bidirec-
tional, so the NO_, NC_, and COM_ pins can be used
as either inputs or outputs.
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
