IC Phoenix
 
Home ›  MM32 > MAX1875EEG-MAX1876EEG,Dual 180 Out-of-Phase PWM Step- Down Controllers with POR
MAX1875EEG-MAX1876EEG Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
MAX1875EEGMAXN/a22avaiDual 180 Out-of-Phase PWM Step- Down Controllers with POR
MAX1876EEGMAXIM N/a220avaiDual 180 Out-of-Phase PWM Step- Down Controllers with POR
MAX1876EEGMAXN/a23avaiDual 180 Out-of-Phase PWM Step- Down Controllers with POR


MAX1876EEG ,Dual 180 Out-of-Phase PWM Step- Down Controllers with PORELECTRICAL CHARACTERISTICS(V+ = 12V, EN = ILIM_ = V , SYNC = GND, I = 0mA, PGND = GND, C = 0.22µF, ..
MAX1876EEG ,Dual 180 Out-of-Phase PWM Step- Down Controllers with PORFeaturesThe MAX1875/MAX1876 dual, synchronized, step-down Two Independent Output Voltagescontrolle ..
MAX1876EEG+ ,Dual 180° Out-of-Phase PWM Step-Down Controllers with PORMAX1875/MAX187619-2431; Rev 0; 7/02Dual 180° Out-of-Phase PWM Step-Down Controllers with POR
MAX1876EEG-T ,Dual 180° Out-of-Phase PWM Step-Down Controllers with PORELECTRICAL CHARACTERISTICS(V+ = 12V, EN = ILIM_ = V , SYNC = GND, I = 0mA, PGND = GND, C = 0.22µF, ..
MAX1879EUA ,Simple / Efficient / 1-Cell Li+ Pulse ChargerELECTRICAL CHARACTERISTICS(V = V = +10V, V = +4.2V, TSEL = GND, GATE = unconnected, ADJ = unconnect ..
MAX1879EUA ,Simple / Efficient / 1-Cell Li+ Pulse ChargerApplicationsOrdering InformationSingle-Cell Li+ Powered PortablesPART TEMP. RANGE PIN-PACKAGESelf- ..
MAX481EESA+T ,±15kV ESD-Protected, Slew-Rate-Limited, Low-Power, RS-485/RS-422 TransceiversELECTRICAL CHARACTERISTICS(V = 5V ±5%, T = T to T , unless otherwise noted.) (Notes 1, 2)CC A MIN M ..
MAX481EPA ,Low-Power / Slew-Rate-Limited RS-485/RS-422 TransceiversMAX481/MAX483/MAX485/MAX487–MAX491/MAX148719-0122; Rev 5; 2/96Low-Power, Slew-Rate-LimitedRS-485/RS ..
MAX481EPA+ ,±15kV ESD-Protected, Slew-Rate-Limited, Low-Power, RS-485/RS-422 TransceiversApplicationsMAX481EESA -40°C to +85°C 8 SOIndustrial-Control Local Area Networks MAX483ECPA 0°C to ..
MAX481ESA ,Low-Power / Slew-Rate-Limited RS-485/RS-422 TransceiversGeneral Description ________
MAX481ESA ,Low-Power / Slew-Rate-Limited RS-485/RS-422 TransceiversFeaturesThe MAX481, MAX483, MAX485, MAX487–MAX491, and' In µMAX Package: Smallest 8-Pin SOMAX1487 a ..
MAX481ESA ,Low-Power / Slew-Rate-Limited RS-485/RS-422 TransceiversFeaturesThe MAX481, MAX483, MAX485, MAX487–MAX491, and' In µMAX Package: Smallest 8-Pin SOMAX1487 a ..


MAX1875EEG-MAX1876EEG
Dual 180 Out-of-Phase PWM Step- Down Controllers with POR
General Description
The MAX1875/MAX1876 dual, synchronized, step-down
controller generates two outputs from input supplies
ranging from 4.75V to 23V. Each output is adjustable from
sub-1V to 18V and supports loads of 10A or higher. Input
voltage ripple and total RMS input ripple current are
reduced by synchronized 180°out-of-phase operation.
The switching frequency is adjustable from 100kHz to
600kHz with an external resistor. Alternatively, the con-
troller can be synchronized to an external clock gener-
ated to another MAX1875/MAX1876 or a system clock.
One MAX1875/MAX1876 can be set to generate an in-
phase, or 90°out-of-phase, clock signal for synchro-
nization with additional controllers. This allows two
controllers to operate either as an interleaved two- or
four-phase system with each output shifted by 90°.
These devices also feature soft-start and soft-stop.
The MAX1875/MAX1876 eliminate the need for current-
sense resistors by utilizing the low-side MOSFET’s on-
resistance as a current-sense element. This protects
the DC-DC components from damage during output-
overload conditions or when output short-circuit faults
without requiring a current-sense resistor. Adjustable
foldback current limit reduces power dissipation during
short-circuit conditions. The MAX1876 includes a
power-on reset output to signal the system when both
outputs reach regulation.
The MAX1875/MAX1876 are available in a 24-pin QSOP
package. An evaluation kit is available to speed designs.
Applications

Network Power Supplies
Telecom Power Supplies
DSP, ASIC, and FPGA Power Supplies
Set-Top Boxes
Broadband Routers
Servers
Features
Two Independent Output Voltages180°Out-of-Phase Operation90°Out-of-Phase Operation
(Using Two MAX1875/MAX1876s)
Foldback Current Limit4.75V to 23V Input Supply Range0 to 18V Output-Voltage Range (Up to 10A)>90% EfficiencyFixed-Frequency Pulse-Width Modulation (PWM)
Operation
Adjustable 100kHz to 600kHz Switching
Frequency
External SYNC InputClock Output for Master/Slave SynchronizationSoft-Start and Soft-StopRSTOutput with 140ms Minimum Delay (MAX1876)Lossless Current Limit (No Sense Resistor)
MAX1875/MAX1876
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR
Pin Configuration
Ordering Information
Typical Operating Circuit appears at end of data sheet.
MAX1875/MAX1876
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR
ABSOLUTE MAXIMUM RATINGS

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
V+ to GND..............................................................-0.3V to +25V
PGND to GND.......................................................-0.3V to +0.3Vto GND..................-0.3V to the lower of +6V and (V+ + 0.3V)
BST1, BST2 to GND...............................................-0.3V to +30V
LX1 to BST1..............................................................-6V to +0.3V
LX2 to BST2..............................................................-6V to +0.3V
DH1 to LX1..............................................-0.3V to (VBST1+ 0.3V)
DH2 to LX2..............................................-0.3V to (VBST2+ 0.3V)
DL1, DL2 to PGND........................................-0.3V to (VL+ 0.3V)
CKO, REF, OSC, ILIM1, ILIM2,
COMP1, COMP2 to GND..........................-0.3V to (VL+ 0.3V)
FB1, FB2, RST, SYNC, EN to GND...........................-0.3V to +6V
VL to GND Short Circuit.............................................Continuous
REF to GND Short Circuit...........................................Continuous
Continuous Power Dissipation (TA= +70°C)
24-Pin QSOP (derate 9.4mW/°C above +70°C)...........762mW
Operating Temperature Range...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s).................................+300°C
ELECTRICAL CHARACTERISTICS

(V+ = 12V, EN = ILIM_ = VL, SYNC = GND, IVL= 0mA, PGND = GND, CREF= 0.22µF, CVL= 4.7µF (ceramic), ROSC= 60kΩ,
MAX1875/MAX1876
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR
ELECTRICAL CHARACTERISTICS (continued)

(V+ = 12V, EN = ILIM_ = VL, SYNC = GND, IVL= 0mA, PGND = GND, CREF= 0.22µF, CVL= 4.7µF (ceramic), ROSC= 60kΩ,
Note 1:
Specifications to -40°C are guaranteed by design and not production tested.
Note 2:
Operating supply range is guaranteed by VLline regulation test. Connect V+ to VLfor 5V operation.
Note 3:
Guaranteed by design and not production tested.
MAX1875/MAX1876
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR
Typical Operating Characteristics

(Circuit of Figure 1, VIN= 12V, TA = +25°C, unless otherwise noted.)
MAX1875/MAX1876
Dual 180°Out-of-Phase PWM Step-
Down Controllers with PORypical Operating Characteristics (continued)

(Circuit of Figure 1, VIN= 12V, TA = +25°C, unless otherwise noted.)
MAX1875/MAX1876
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR
Detailed Description
DC-DC PWM Controller

The MAX1875/MAX1876 step-down converters use a
PWM voltage-mode control scheme (Figure 2) for each
out-of-phase controller. The controller generates the
clock signal by dividing down the internal oscillator or
SYNC input when driven by an external clock, so each
controller’s switching frequency equals half the oscillator
frequency (fSW= fOSC/2). An internal transconductance
error amplifier produces an integrated error voltage at
the COMP pin, providing high DC accuracy. The voltage
at COMP sets the duty cycle using a PWM comparator
and a ramp generator. At each rising edge of the clock,
REG1’s high-side N-channel MOSFET turns on and
remains on until either the appropriate duty cycle or until
the maximum duty cycle is reached. REG2 operates out-
of-phase, so the second high-side MOSFET turns on at
each falling edge of the clock. During each high-side
MOSFET’s on-time, the associated inductor current
ramps up.
During the second-half of the switching cycle, the high-
side MOSFET turns off and the low-side N-channel
MOSFET turns on. Now the inductor releases the stored
energy as its current ramps down, providing current to
the output. Under overload conditions, when the induc-
tor current exceeds the selected valley current-limit (see
the Current-Limit Circuit (ILIM_) section), the high-side
MOSFET does not turn on at the appropriate clock edge
and the low-side MOSFET remains on to let the inductor
current ramp down.
Synchronized Out-of-Phase Operation

The two independent regulators in the MAX1875/
MAX1876 operate 180°out-of-phase to reduce input fil-
tering requirements, reduce electromagnetic interference
(EMI), and improve efficiency. This effectively lowers
component cost and saves board space, making the
MAX1875/MAX1876 ideal for cost-sensitive applications.
Dual-switching regulators typically operate both
controllers in-phase, and turn on both high-side
MOSFETs at the same time. The input capacitor must
then support the instantaneous current requirements of
both controllers simultaneously, resulting in increased
ripple voltage and current when compared to a single
switching regulator. The higher RMS ripple current
lowers efficiency due to power loss associated with the
input capacitor’s effective series resistance (ESR). This
typically requires more low-ESR input capacitors in
parallel to minimize input voltage ripple and ESR-related
losses, or to meet the necessary ripple-current rating.
MAX1875/MAX1876
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR
MAX1875/MAX1876
With dual synchronized out-of-phase operation, the
MAX1875/MAX1876’s high-side MOSFETs turn-on 180°
out-of-phase. The instantaneous input current peaks of
both regulators no longer overlap, resulting in reduced
RMS ripple current and input voltage ripple. This reduces
the required input capacitor ripple-current rating, allow-
ing fewer or less expensive capacitors, and reduces
shielding requirements for EMI. The Out-of-Phase
Waveforms in the Typical Operating Characteristics
demonstrate synchronized 180°out-of-phase operation.
Internal 5V Linear Regulator (VL)

All MAX1875/MAX1876 functions are internally powered
from an on-chip, low-dropout 5V regulator. The maxi-
mum regulator input voltage (V+) is 23V. Bypass the
regulator’s output (VL) with a 4.7µF ceramic capacitor
to PGND. The VLdropout voltage is typically 500mV, so
when V+ is greater than 5.5V, VLis typically 5V. The
MAX1875/MAX1876 also employs an undervoltage
lockout circuit that disables both regulators when VL
falls below 4.5V. VLshould also be bypassed to GND
with a 0.1µF capacitor.
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR
The internal VLlinear regulator can source over 50mA to
supply the IC, power the low-side gate driver, charge the
external boost capacitor, and supply small external
loads. When driving large FETs, little or no regulator cur-
rent may be available for external loads.
For example, when switched at 600kHz, a single large
FET with 18nC total gate charge requires 18nC ✕600kHz
= 11mA. To drive larger MOSFETs, or deliver larger
loads, connect VLto an external power supply from
4.75V to 5.5V.
MAX1875/MAX1876
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR

Figure 2. Functional Diagram
MAX1875/MAX1876
High-Side Gate-Drive Supply (BST_)

Gate-drive voltages for the high-side N-channel switch-
es are generated by the flying-capacitor boost circuits
(Figure 3). A boost capacitor (connected from BST_ to
LX_) provides power to the high-side MOSFET driver.
On startup, the synchronous rectifier (low-side MOSFET)
forces LX_ to ground and charges the boost capacitor to
5V. On the second half-cycle, after the low-side MOSFET
turns off, the high-side MOSFET is turned on by closing
an internal switch between BST_ and DH_. This provides
the necessary gate-to-source voltage to turn on the high-
side switch, an action that boosts the 5V gate-drive
signal above VIN. The current required to drive the high-
side MOSFET gates (fSWITCH ✕ QG) is ultimately drawn
from VL.
MOSFET Gate Drivers (DH_, DL_)

The DH and DL drivers are optimized for driving moder-
ate-size N-channel high-side and larger low-side power
MOSFETs. This is consistent with the low-duty factor
seen with large VIN- VOUTdifferential. The DL_ low-side
drive waveform is always the complement of the DH_
high-side drive waveform (with controlled dead time to
prevent cross-conduction or “shoot-through”). An adap-
tive dead-time circuit monitors the DL_ output and pre-
vents the high-side FET from turning on until DL_ is fully
off. There must be a low-resistance, low-inductance
path from the DL_ driver to the MOSFET gate in order
for the adaptive dead-time circuit to work properly.
Otherwise, the sense circuitry in the MAX1875/MAX1876
interprets the MOSFET gate as “off” while there is actu-
ally charge still left on the gate. Use very short, wide
traces (50mils to 100mils wide if the MOSFET is 1in from
the device). The dead time at the DH-off edge is deter-
mined by a fixed 30ns internal delay.
Synchronous rectification reduces conduction losses in
the rectifier by replacing the normal low-side Schottky
catch diode with a low-resistance MOSFET switch.
Additionally, the MAX1875/MAX1876 uses the synchro-
nous rectifier to ensure proper startup of the boost gate-
driver circuit and to provide the current-limit signal.
The internal pulldown transistor that drives DL_ low is
robust, with a 0.5Ω(typ) on-resistance. This low on-
resistance helps prevent DL_ from being pulled up dur-
ing the fast rise-time of the LX_ node, due to capacitive
coupling from the drain to the gate of the low-side syn-
chronous-rectifier MOSFET. However, for high-current
applications, some combinations of high- and low-side
FETs can cause excessive gate-drain coupling, leading
to poor efficiency, EMI, and shoot-through currents.
This can be remedied by adding a resistor (typically
less than 5Ω) in series with BST_, which increases the
turn-on time of the high-side FET without degrading the
turn-off time (Figure 3).
Current-Limit Circuit (ILIM_)

The current-limit circuit employs a “valley” current-sens-
ing algorithm that uses the on-resistance of the low-side
MOSFET as a current-sensing element. If the current-
sense signal is above the current-limit threshold, the
MAX1875/MAX1876 does not initiate a new cycle
(Figure 4). Since valley current sensing is employed, the
actual peak current is greater than the current-limit
threshold by an amount equal to the inductor ripple cur-
rent. Therefore, the exact current-limit characteristic and
maximum load capability are a function of the low-side
MOSFET’s on-resistance, current-limit threshold, induc-
tor value, and input voltage. The reward for this uncer-
tainty is robust, lossless overcurrent sensing that does
not require costly sense resistors.
The adjustable current limit accommodates MOSFETs
with a wide range of on-resistance characteristics (see
the Design Proceduresection). The current-limit thresh-
old is adjusted with an external resistor at ILIM_ (Figure
1). The adjustment range is from 50mV to 300mV, cor-
responding to resistor values of 100kΩto 600kΩ. In
adjustable mode, the current-limit threshold across the
low-side MOSFET is precisely 1/10th the voltage seen
at ILIM_. However, the current-limit threshold defaults
to 100mV when ILIM is tied to VL. The logic threshold
for switchover to this 100mV default value is approxi-
mately VL- 0.5V.
Adjustable foldback current limit reduces power dissi-
pation during short-circuit conditions (see the Design
Proceduresection).
Carefully observe the PC board layout guidelines to
ensure that noise and DC errors do not corrupt the cur-
rent-sense signals seen by LX_ and PGND. The IC
must be mounted close to the low-side MOSFET with
short, direct traces making a Kelvin sense connection
so that trace resistance does not add to the intended
sense resistance of the low-side MOSFET.
Undervoltage Lockout and Startup

If VLdrops below 4.5V, the MAX1875/MAX1876 assumes
that the supply and reference voltages are too low to
make valid decisions and activates the undervoltage lock-
out (UVLO) circuitry which forces DL and DH low to inhibit
switching. RSTis also forced low during UVLO. After VL
rises above 4.5V, the controller powers up the outputs.
Enable (EN), Soft-Start, and Soft-Stop

Pull EN high to enable or low to shutdown both regula-
tors. During shutdown the supply current drops to 1mA
(max), LX enters a high-impedance state (DH_ con-
nected to LX_, and DL_ connected to PGND), and
COMP_ is discharged to GND through a 17Ωresistor.and REF remain active in shutdown. For “always-on”
operation, connect EN to VL.
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR
On the rising edge of EN both controllers enter soft-
start. Soft-start gradually ramps up to the reference
voltage seen by the error amplifier in order to control
the outputs’ rate of rise and reduce input surge cur-
rents during startup. The soft-start period is 1024 clock
cycles (1024/fSW), and the internal soft-start DAC
ramps up the voltage in 64 steps. The output reaches
regulation when soft-start is completed. On the falling
edge of EN both controllers simultaneously enter soft-
stop, which reverses the soft-start ramp. The part
enters shutdown after soft-stop is complete.
Reset Output (MAX1876 Only)

RSTis an open-drain output. RSTpulls low when either
output falls below 90% of its nominal regulation voltage.
Once both outputs exceed 90% of their nominal regulation
voltages and both soft-start cycles are completed, RST
goes high impedance. To obtain a logic-voltage output,
connect a pullup resistor from RSTto the logic supply volt-
age. A 100kΩresistor works well for most applications. If
unused, leave RSTgrounded or unconnected.
Clock Synchronization (SYNC, CKO)

SYNC serves two functions: SYNC selects the clock
output (CKO) type used to synchronize slave con-
trollers, or it serves as a clock input so the
MAX1875/MAX1876 can be synchronized with an exter-
nal clock signal. This allows the MAX1875/MAX1876 to
funtion as either a master or slave. CKO provides a
clock signal synchronized to the MAX1875/MAX1876s’
switching frequency, allowing either in-phase (SYNC =
GND) or 90°out-of-phase (SYNC = VL) synchronization
of additional DC-DC controllers (Figure 5). The
MAX1875/MAX1876 support the following three operat-
ing modes:SYNC = GND:The CKO output frequency equals
REG1’s switching frequency (fCKO= fDH1) and the
CKO signal is in phase with REG1’s switching fre-
quency. This provides 2-phase operation when syn-
chronized with a second slave controller.SYNC = VL:The CKO output frequency equals two
times REG1’s switching frequency (fCKO= 2fDH1)
and the CKO signal is phase shifted by 90°with
respect to REG1’s switching frequency. This pro-
vides 4-phase operation when synchronized with a
second MAX1875/MAX1876 (slave controller).SYNC Driven by External Oscillator:The controller
generates the clock signal by dividing down the
SYNC input signal, so that the switching frequency
equals half the synchronization frequency (fSW=
fSYNC/2). REG1’s conversion cycles initiate on the ris-
ing edge of the internal clock signal. The CKO output
frequency and phase match REG1’s switching fre-
quency (fCKO= fDH1) and the CKO signal is in
phase. Note that the MAX1875/MAX1876 still require
ROSCwhen SYNC is externally clocked and the inter-
nal oscillator frequency should be set to 50% of the
synchronization frequency (fOSC= 0.5fSYNC).
Thermal Overload Protection

Thermal overload protection limits total power dissipation
in the MAX1875/MAX1876. When the device’s die-junc-
tion temperature exceeds TJ= +160°C, an on-chip ther-
mal sensor shuts down the device, forcing DL_ and DH_
low, allowing the IC to cool. The thermal sensor turns the
part on again after the junction temperature cools by
10°C. During thermal shutdown, the regulators shut
down, RSTgoes low, and soft-start is reset. If the VLlin-
ear-regulator output is short-circuited, thermal-overload
protection is triggered.
Design Procedure
Effective Input Voltage Range

Although, the MAX1875/MAX1876 controllers can oper-
ate from input supplies ranging from 4.75V to 23V, the
input voltage range can be effectively limited by the
MAX1875/MAX1876s’ duty-cycle limitations. The maxi-
mum input voltage is limited by the minimum on-time
(tON(MIN)):
MAX1875/MAX1876
Dual 180°Out-of-Phase PWM Step-
Down Controllers with POR
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED