M74HC4060RM13TR ,14 STAGE BINARY COUNTER/OSCILLATORlogic diagram has not be used to estimate propagation delays2/12M74HC4060
M74HC4060RM13TR ,14 STAGE BINARY COUNTER/OSCILLATORABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage-0.5 to +7 VCCV DC Input V ..
M74HC4066M1R ,QUAD BILATERAL SWITCHAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HC4066RM13TR ,QUAD BILATERAL SWITCHLOGIC DIAGRAM PIN DESCRIPTION PIN No SYMBOL NAME AND FUNCTION1, 4, 8, 11 1 to 4 I/O Independe ..
M74HC4066TTR ,QUAD BILATERAL SWITCHM74HC4066QUAD BILATERAL SWITCH ■ HIGH SPEED: t = 7ns (TYP.) at V = 6VPD CC■ LOW POWER DISSIPATION: ..
M74HC4072M1R ,DUAL 4 INPUT OR GATEAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
MAX1482CSD ,20A, 1.8-Unit-Load, Slew-Rate-Limited RS-485 TransceiversFeaturesThe MAX1482 and MAX1483 are low-power trans-' Low 20µA Operating Currentceivers for RS-485 ..
MAX1482CSD ,20A, 1.8-Unit-Load, Slew-Rate-Limited RS-485 TransceiversApplicationsMAX1483CPA 0°C to +70°C 8 Plastic DIPIndustrial-Control Local Area NetworksMAX1483CSA 0 ..
MAX1482CSD+ ,20µA, 1/8-Unit-Load, Slew-Rate-Limited, RS-485 TransceiversMAX1482/MAX148319-0367; Rev 1; 5/06120µA, ⁄ -Unit-Load, Slew-Rate-Limited8RS-485 Transceivers______ ..
MAX1482CSD+ ,20µA, 1/8-Unit-Load, Slew-Rate-Limited, RS-485 TransceiversApplicationsMAX1482ESD -40°C to +85°C 14 SO S14-4Industrial-Control Local Area NetworksMAX1483CPA 0 ..
MAX1482CSD+T ,20µA, 1/8-Unit-Load, Slew-Rate-Limited, RS-485 TransceiversELECTRICAL CHARACTERISTICS(V = 5V ±5%, T = T to T , unless otherwise noted. Typical values are at T ..
MAX1482EPD ,20A, 1.8-Unit-Load, Slew-Rate-Limited RS-485 TransceiversApplicationsMAX1482CSD 0°C to +70°C 14 SOLow-Power RS-485/RS-422 Networks MAX1482EPD -40°C to +85°C ..
M74HC4060B1R-M74HC4060M1R-M74HC4060RM13TR
14 STAGE BINARY COUNTER/OSCILLATOR
1/12July 2001 HIGH SPEED:
fMAX = 65MHz (TYP.) at VCC = 6V LOW POWER DISSIPATION:
ICC =4μA(MAX.) at TA=25°C HIGH NOISE IMMUNITY:NIH = VNIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:OH | = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: PLH ≅ t PHL WIDE OPERATING VOLTAGE RANGE:
VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 4060
DESCRIPTIONThe M74HC4060 is an high speed CMOS
14-STAGE BINARY COUNTER/OSCILLATOR
fabricated with silicon gate C2 MOS technology.
The oscillator configuration allows design of either
RC or crystal oscillator circuits. A high level on the
CLEAR accomplishes the reset function, i.e. all
counter outputs are made low and the oscillator is
disabled.
A negative transition on the clock input increments
the counter. Ten kinds of divided output are
provided; 4 to 10 and 12 to 14 stage inclusive. The
maximum division available at Q12 is 1/16384 f
oscillator.
The Ø1 input and the CLEAR input are equipped
with protection circuits against static discharge
and transient excess voltage.
M74HC406014 STAGE BINARY COUNTER/OSCILLATOR
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HC40602/12
IINPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X : Don’t Care
LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays
M74HC40603/12
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
M74HC40604/12
DC SPECIFICATIONS
M74HC40605/12
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC
M74HC40606/12
TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM 1: PROPAGATION DELAY TIMES, MINIMUM PULSE WIDTH (ØI) (f=1MHz; 50% duty cycle)
