IC Phoenix
 
Home ›  MM12 > M58LW064C110N6-M58LW064C110ZA6T,64 MBIT (4MB X16, UNIFORM BLOCK, BURST)3V SUPPLY FLASH MEMORY
M58LW064C110N6-M58LW064C110ZA6T Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
M58LW064C110N6STN/a501avai64 MBIT (4MB X16, UNIFORM BLOCK, BURST)3V SUPPLY FLASH MEMORY
M58LW064C110ZA6TSTMicroelectronicsN/a743avai64 MBIT (4MB X16, UNIFORM BLOCK, BURST)3V SUPPLY FLASH MEMORY


M58LW064C110ZA6T ,64 MBIT (4MB X16, UNIFORM BLOCK, BURST)3V SUPPLY FLASH MEMORYFEATURES SUMMARY■ WIDE x16 DATA BUS for HIGH BANDWIDTH Figure 1. Packages■ SUPPLY VOLTAGE–V = 2.7 t ..
M58LW064D ,64 MBIT(8MB X8, 4MB X16, UNIFORM BLOCK)3V SUPPLY FLASH MEMORYLogic Diagram . 6Table 1. Signal Names . . 6Figure 3. TSOP56 Connections . . . ..
M58LW064D ,64 MBIT(8MB X8, 4MB X16, UNIFORM BLOCK)3V SUPPLY FLASH MEMORYFEATURES SUMMARY

M58LW064C110N6-M58LW064C110ZA6T
64 MBIT (4MB X16, UNIFORM BLOCK, BURST)3V SUPPLY FLASH MEMORY
1/61August 2004
M58LW064C

64 Mbit (4Mb x 16, Uniform Block, Burst)
3V Supply Flash Memory
FEATURES SUMMARY
WIDE x16 DATA BUS for HIGH BANDWIDTH SUPPLY VOLTAGE
–VDD = 2.7 to 3.6V core supply voltage for
Program, Erase and Read operations
–VDDQ = 1.8 to VDD for I/O Buffers SYNCHRONOUS/ASYNCHRONOUS READ Synchronous Burst read Asynchronous Random Read Asynchronous Address Latch Controlled
Read Page Read ACCESS TIME Synchronous Burst Read up to 56MHz Asynchronous Page Mode Read 110/
25ns Random Read 110ns PROGRAMMING TIME 16 Word Write Buffer 12µs Word effective programming time 64 UNIFORM 64 KWord MEMORY BLOCKS ENHANCED SECURITY Block Protection/ Unprotection Smart Protection: irreversible block
locking system
–VPEN signal for Program Erase Enable 128 bit Protection Register with 64 bit
Unique Code in OTP area PROGRAM and ERASE SUSPEND COMMON FLASH INTERFACE 100,000 PROGRAM/ERASE CYCLES per
BLOCK ELECTRONIC SIGNATURE Manufacturer Code: 0020h Device Code M58LW064C : 8820h PACKAGES Compliant with Lead-Free Soldering
Processes Lead-Free Versions
M58LW064C
TABLE OF CONTENTS
FEATURES SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Figure 1. Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SUMMARY DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Figure 2. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Table 1. Signal Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 3. TSOP56 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Figure 4. TBGA64 Connections (Top view through package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Figure 5. Block Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
SIGNAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Address Inputs (A1-A22). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Data Inputs/Outputs (DQ0-DQ15). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Chip Enable (E). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Output Enable (G). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Write Enable (W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Reset/Power-Down (RP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Latch Enable (L). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Clock (K).. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Valid Data Ready (R). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Status/(Ready/Busy) (STS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Program/Erase Enable (VPEN). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
VDD Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
VDDQ Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
VSS Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
VSSQ Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
BUS OPERATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Address Latch.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Bus Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Bus Write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Output Disable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Power-Down. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Table 2. Bus Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
READ MODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Asynchronous Read Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Asynchronous Latch Controlled Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Asynchronous Random Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Asynchronous Page Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Synchronous Read Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Synchronous Burst Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3/61
M58LW064C

Single Synchronous Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CONFIGURATION REGISTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Read Select Bit (CR15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
X-Latency Bits (CR13-CR11). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Internal Clock Divider Bit (CR10). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Y-Latency Bit (CR9). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Valid Data Ready Bit (CR8). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Burst Type Bit (CR7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Valid Clock Edge Bit (CR6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Burst Length Bit (CR2-CR0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Table 3. Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Table 4. Burst Type Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Figure 6. Burst Configuration X-1-1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Figure 7. Burst Configuration X-2-2-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
COMMAND INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Read Memory Array Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Read Electronic Signature Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Read Query Command.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Read Status Register Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Clear Status Register Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Block Erase Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Word Program Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Write to Buffer and Program Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Program/Erase Suspend Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Program/Erase Resume Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Set Configuration Register Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Block Protect Command.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Blocks Unprotect Command.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Protection Register Program Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Configure STS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Table 5. Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Table 6. Configuration Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Table 7. Read Electronic Signature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Table 8. Read Protection Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Figure 8. Protection Register Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Table 9. Program, Erase Times and Program Erase Endurance Cycles . . . . . . . . . . . . . . . . . . .25
STATUS REGISTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Program/Erase Controller Status Bit (SR7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Erase Suspend Status Bit (SR6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Erase Status Bit (SR5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Program Status Bit (SR4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
VPEN Status Bit (SR3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Program Suspend Status Bit (SR2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
M58LW064C
Block Protection Status Bit (SR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Reserved (SR0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Table 10. Status Register Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Table 11. Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DC and AC PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Table 12. Operating and AC Measurement Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Figure 9. AC Measurement Input Output Waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Figure 10.AC Measurement Load Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Table 13. Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Table 14. DC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Figure 11.Asynchronous Random Read AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Table 15. Asynchronous Random Read AC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Figure 12.Asynchronous Latch Controlled Read AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . .32
Table 16. Asynchronous Latch Controlled Read AC Characteristics . . . . . . . . . . . . . . . . . . . . . . .33
Figure 13.Asynchronous Page Read AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Table 17. Asynchronous Page Read AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Figure 14.Asynchronous Write AC Waveform, Write Enable Controlled. . . . . . . . . . . . . . . . . . . . .34
Figure 15.Asynchronous Latch Controlled Write AC Waveform, Write Enable Controlled . . . . . . .35
Table 18. Asynchronous Write and Latch Controlled Write AC Characteristics, W Controlled. . . .36
Figure 16.Asynchronous Write AC Waveforms, Chip Enable Controlled . . . . . . . . . . . . . . . . . . . .37
Figure 17.Asynchronous Latch Controlled Write AC Waveforms, Chip Enable Controlled. . . . . . .37
Table 19. Asynchronous Write and Latch Controlled Write AC Characteristics, E Controlled . .38
Figure 18.Synchronous Burst Read AC Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Figure 19.Synchronous Burst Read, Continuous, Valid Data Ready Output . . . . . . . . . . . . . . . . .40
Table 20. Synchronous Burst Read AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Figure 20.Reset, Power-Down and Power-up AC Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Table 21. Reset, Power-Down and Power-up AC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . .41
PACKAGE MECHANICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Figure 21.TSOP56 - 56 lead Plastic Thin Small Outline, 14 x 20 mm, Package Outline . . . . . . . .42
Table 22. TSOP56 - 56 lead Plastic Thin Small Outline, 14 x 20 mm, Package Mechanical Data.42
Figure 22.TBGA64 10x13mm - 8x8 ball array, 1mm pitch, Package Outline . . . . . . . . . . . . . . . . .43
Table 23. TBGA64 10x13mm - 8x8 ball array, 1mm pitch, Package Mechanical Data. . . . . . . . . .43
PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Table 24. Ordering Information Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
APPENDIX A.BLOCK ADDRESS TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Table 25. Block Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
APPENDIX B.COMMON FLASH INTERFACE - CFI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Table 26. Query Structure Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
5/61
M58LW064C

Table 27. CFI - Query Address and Data Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Table 28. CFI - Device Voltage and Timing Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Table 29. Device Geometry Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Table 30. Block Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Table 31. Extended Query information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
APPENDIX C.FLOW CHARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Figure 23.Write to Buffer and Program Flowchart and Pseudo Code . . . . . . . . . . . . . . . . . . . . . . .50
Figure 24.Program Suspend & Resume Flowchart and Pseudo Code . . . . . . . . . . . . . . . . . . . . . .51
Figure 25.Erase Flowchart and Pseudo Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Figure 26.Erase Suspend & Resume Flowchart and Pseudo Code . . . . . . . . . . . . . . . . . . . . . . . .53
Figure 27.Block Protect Flowchart and Pseudo Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Figure 28.Block Unprotect Flowchart and Pseudo Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Figure 29.Protection Register Program Flowchart and Pseudo Code. . . . . . . . . . . . . . . . . . . . . . .56
Figure 30.Command Interface and Program Erase Controller Flowchart (a) . . . . . . . . . . . . . . . . .57
Figure 31.Command Interface and Program Erase Controller Flowchart (b) . . . . . . . . . . . . . . . . .58
Figure 32.Command Interface and Program Erase Controller Flowchart (c). . . . . . . . . . . . . . . . . .59
REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Table 32. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
M58LW064C
SUMMARY DESCRIPTION

M58LW064C is a 64 Mbit (4Mb x16) non-volatile
memory that can be read, erased and repro-
grammed. These operations can be performed us-
ing a single low voltage (2.7V to 3.6V) core supply.
On power-up the memory defaults to Read mode
with an asynchronous bus where it can be read in
the same way as a non-burst Flash memory.
The memory is divided into 64 blocks of 1Mbit that
can be erased independently so it is possible to
preserve valid data while old data is erased. Pro-
gram and Erase commands are written to the
Command Interface of the memory. An on-chip
Program/Erase Controller simplifies the process of
programming or erasing the memory by taking
care of all of the special operations that are re-
quired to update the memory contents. The end of
a program or erase operation can be detected and
any error conditions identified in the Status Regis-
ter. The command set required to control the
memory is consistent with JEDEC standards.
The device supports synchronous burst read and
asynchronous read from all blocks of the memory
array; at power-up the device is configured for
asynchronous read. In asynchronous mode an
Address Latch input can be used to latch address-
es in Latch Controlled mode. In synchronous burst
mode, data is output on each clock cycle at fre-
quencies of up to 56MHz.
The Write Buffer allows the microprocessor to pro-
gram from 1 to 16 Words in parallel, both speeding
up the programming and freeing up the micropro-
cessor to perform other work. A Word Program
command is available to program a single Word.
Erase can be suspended in order to perform either
Read or Program in any other block and then re-
sumed. Program can be suspended to read data in
any other block and then resumed. Each block can
be programmed and erased over 100,000 cycles.
The M58LW064C has several security features to
increase data protection. Block Protection, where each block can be
individually protected against program or
erase operations. All blocks are protected
during power-up. The protection of the blocks
is non-volatile; after power-up the protection
status of each block is restored to the state
when power was last removed. Program Erase Enable input VPEN, program or
erase operations are not possible when the
Program Erase Enable input VPEN is low. Smart Protection, which allows protected
blocks to be permanently locked. This feature
is not described in the datasheet for security
reasons. Please contact STMicroelectronics
for further details. 128 bit Protection Register, divided into two 64
bit segments: the first contains a unique
device number written by ST, the second is
user programmable. The user programmable
segment can be protected.
The Reset/Power-Down pin is used to apply a
Hardware Reset to the memory and to set the de-
vice in power-down mode.
The device features an Auto Low Power mode. If
the bus becomes inactive during Asynchronous
Read operations, the device automatically enters
Auto Low Power mode. In this mode the power
consumption is reduced to the Auto Low Power
supply current.
The STS signal is an open drain output that can be
used to identify the Program/Erase Controller sta-
tus. It can be configured in two modes: Ready/
Busy mode where a static signal indicates the sta-
tus of the P/E.C, and Status mode where a pulsing
signal indicates the end of a Program or Block
Erase operation. In Status mode it can be used as
a system interrupt signal, useful for saving CPU
time.
The memory is available in TSOP56 (14 x 20 mm)
and TBGA64 (10 x 13mm, 1mm pitch) packages.
In addition to the standard version, the packages
are also available in Lead-free version, in compli-
ance with JEDEC Std J-STD-020B, the ST ECO-
PACK 7191395 Specification, and the RoHS
(Restriction of Hazardous Substances) directive.
All packages are compliant with Lead-free solder-
ing processes.
7/61
M58LW064C Table 1. Signal Names
M58LW064C
9/61
M58LW064C
M58LW064C
11/61
M58LW064C
SIGNAL DESCRIPTIONS

See Figure 2., Logic Diagram, and Table
1., Signal Names, for a brief overview of the sig-
nals connected to this device.
Address Inputs (A1-A22).
The Address Inputs
are used to select the cells to access in the mem-
ory array during Bus Read operations either to
read or to program data to. During Bus Write oper-
ations they control the commands sent to the
Command Interface of the internal state machine.
Chip Enable and Latch Enable must be low when
selecting the addresses.
The address inputs are latched on the rising edge
of Chip Enable, Write Enable or Latch Enable,
whichever occurs first in a Write operation. The
address latch is transparent when Latch Enable is
low, VIL. The address is internally latched in an
Erase or Program operation.
Data Inputs/Outputs (DQ0-DQ15).
The Data In-
puts/Outputs output the data stored at the selected
address during a Bus Read operation, or are used
to input the data during a program operation. Dur-
ing Bus Write operations they represent the com-
mands sent to the Command Interface of the
internal state machine. When used to input data or
Write commands they are latched on the rising
edge of Write Enable or Chip Enable, whichever
occurs first.
When Chip Enable and Output Enable are both
low, VIL, the data bus outputs data from the mem-
ory array, the Electronic Signature, the Block Pro-
tection status, the CFI Information or the contents
of the Status Register. The data bus is high imped-
ance when the chip is deselected, Output Enable
is high, VIH, or the Reset/Power-Down signal is
low, VIL. When the Program/Erase Controller is
active the Ready/Busy status is given on DQ7.
Chip Enable (E).
The Chip Enable, E, input acti-
vates the memory control logic, input buffers, de-
coders and sense amplifiers. Chip Enable, E, at
VIH deselects the memory and reduces the power
consumption to the Standby level, IDD1.
Output Enable (G).
The Output Enable, G, gates
the outputs through the data output buffers during
a read operation. When Output Enable, G, is at VIH
the outputs are high impedance. Output Enable,
G, can be used to inhibit the data output during a
burst read operation.
Write Enable (W).
The Write Enable input, W,
controls writing to the Command Interface, Input
Address and Data latches. Both addresses and
data can be latched on the rising edge of Write En-
able (also see Latch Enable, L).
Reset/Power-Down (RP).
The Reset/Power-
Down pin can be used to apply a Hardware Reset
to the memory.
A Hardware Reset is achieved by holding Reset/
Power-Down Low, VIL, for at least tPLPH. When
Reset/Power-Down is Low, VIL, the Status Regis-
ter information is cleared and the power consump-
tion is reduced to power-down level. The device is
deselected and outputs are high impedance. If Re-
set/Power-Down goes low, VIL,during a Block
Erase, a Write to Buffer and Program or a Block
Protect/Unprotect the operation is aborted and the
data may be corrupted. In this case the Ready/
Busy pin stays low, VIL, for a maximum timing of
tPLPH + tPHRH, until the completion of the Reset/
Power-Down pulse.
After Reset/Power-Down goes High, VIH, the
memory will be ready for Bus Read and Bus Write
operations after tPHQV. Note that Ready/Busy
does not fall during a reset, see Ready/Busy Out-
put section.
In an application, it is recommended to associate
Reset/Power-Down pin, RP, with the reset signal
of the microprocessor. Otherwise, if a reset opera-
tion occurs while the memory is performing an
Erase or Program operation, the memory may out-
put the Status Register information instead of be-
ing initialized to the default Asynchronous
Random Read.
Latch Enable (L).
The Bus Interface is config-
ured to latch the Address Inputs on the rising edge
of Latch Enable, L. In synchronous bus operations
the address is latched on the active edge of the
Clock when Latch Enable is Low, VIL or on the ris-
ing of Latch Enable, whichever occurs first. Once
latched, the addresses may change without affect-
ing the address used by the memory. When Latch
Enable is Low, VIL, the latch is transparent.
Clock (K).
The Clock, K, is used to synchronize
the memory with the external bus during synchro-
nous read operations. The Clock can be config-
ured to have an active rising or falling edge. Bus
signals are latched on the active edge of the Clock
during synchronous bus operations. In Synchro-
nous Burst Read mode the address is latched on
the first active clock edge when Latch Enable is
low, VIL, or on the rising edge of Latch Enable,
whichever occurs first.
During asynchronous bus operations the Clock is
not used.
Valid Data Ready (R).
The Valid Data Ready
output, R, is an open drain output that can be used
to identify if the memory is ready to output data or
not. The Valid Data Ready output is only active
during Synchronous Burst Read operations when
the Burst Length is set to Continuous. The Valid
Data Ready output can be configured to be active
on the clock edge of the invalid data read cycle or
one cycle before. Valid Data Ready Low, VOL, in-
M58LW064C
dicates that the data is not, or will not be valid. Val-
id Data Ready in a high-impedance state indicates
that valid data is or will be available.
Unless Synchronous Burst Read has been select-
ed, Valid Data Ready is high-impedance. It may be
tied to other components with the same Valid Data
Ready signal to create a unique System Ready
signal.
The Valid Data Ready, R, output has an internal
pull-up resistor of approximately 1 MΩ powered
from VDDQ, designers should use an external pull-
up resistor of the correct value to meet the external
timing requirements for Valid Data Ready rising.
Refer to Figure 19.
Status/(Ready/Busy) (STS).
The STS signal is
an open drain output that can be used to identify
the Program/Erase Controller status. It can be
configured in two modes: Ready/Busy - the pin is Low, VOL, during
program and erase operations and high
impedance when the memory is ready for any
read, program or erase operation. Status - the pin gives a pulsing signal to
indicate the end of a program or Block Erase
operation.
After power-up or reset the STS pin is configured
in Ready/Busy mode. The pin can be configured
for Status mode using the Configure STS com-
mand.
When the Program/Erase Controller is idle, or sus-
pended, STS can float High through a pull-up re-
sistor. The use of an open-drain output allows the
STS pins from several memories to be connected
to a single pull-up resistor (a Low will indicate that
one, or more, of the memories is busy).
STS is not Low during a reset unless the reset was
applied when the Program/Erase controller was
active. Ready/Busy can rise before Reset/Power-
Down rises.
Program/Erase Enable (VPEN).
The Program/
Erase Enable input, VPEN, is used to protect all
blocks, preventing program and erase operations
from affecting their data.
Program/Erase Enable must be kept High during
all Program/Erase Controller operations, other-
wise the operations is not guaranteed to succeed
and data may become corrupt.
VDD Supply Voltage.
VDD provides the power
supply to the internal core of the memory device.
It is the main power supply for all operations
(Read, Program and Erase).
VDDQ Supply Voltage.
VDDQ provides the power
supply to the I/O pins and enables all Outputs to
be powered independently from VDD. VDDQ can be
tied to VDD or can use a separate supply.
It is recommended to power-up and power-down
VDD and VDDQ together to avoid any condition that
would result in data corruption.
VSS Ground.
Ground, VSS, is the reference for
the core power supply. It must be connected to the
system ground.
VSSQ Ground.
VSSQ ground is the reference for
the input/output circuitry driven by VDDQ. VSSQ
must be connected to VSS.
Note: Each device in a system should have
VDD and VDDQ decoupled with a 0.1µF ceramic
capacitor close to the pin (high frequency, in-
herently low inductance capacitors should be
as close as possible to the package). See Fig-
ure 10., AC Measurement Load Circuit.
13/61
M58LW064C
BUS OPERATIONS

There are six standard bus operations that control
the device. These are Address Latch, Bus Read,
Bus Write, Output Disable, Power-Down and
Standby. See Table 2., Bus Operations, for a sum-
mary.
Typically glitches of less than 5ns on Chip Enable
or Write Enable are ignored by the memory and do
not affect Bus Write operations.
Address Latch.
Address latch operations input
valid addresses.
A valid bus operation involves setting the desired
address on the Address Inputs, setting Chip En-
able and Latch Enable Low, VIL and keeping Write
Enable High, VIH; the address is latched on the ris-
ing edge of Address Latch.
Bus Read.
Bus Read operations are used to out-
put the contents of the Memory Array, the Elec-
tronic Signature, the Status Register, the Common
Flash Interface and the Block Protection Status.
A valid bus operation involves setting the desired
address on the Address Inputs, applying a Low
signal, VIL, to Chip Enable, Output Enable and
Latch Enable and keeping Write Enable High, VIH.
The data read depends on the previous command
written to the memory (see Command Interface
section). See Figures 11, 12, 13, 18 and 19 Read
AC Waveforms, and Tables 15, 16, 17 and 20
Read AC Characteristics, for details of when the
output becomes valid.
Bus Write.
Bus Write operations write Com-
mands to the memory or latch addresses and input
data to be programmed.
A valid Bus Write operation begins by setting the
desired address on the Address Inputs and setting
Latch Enable Low, VIL. The Address Inputs are
latched by the Command Interface on the rising
edge of Chip Enable or Write Enable, whichever
occurs first. The Data Inputs/Outputs are latched
by the Command Interface on the rising edge of
Chip Enable or Write Enable, whichever occurs
first. Output Enable must remain High, VIH, during
the Bus Write operation.
See Figures 14, 15, 16 and 17, Write AC Wave-
forms, and Tables 18 and 19, Write AC Character-
istics, for details of the timing requirements.
Output Disable.
The Data Inputs/Outputs are
high impedance when the Output Enable is at VIH.
Power-Down.
The memory is in Power-Down
mode when Reset/Power-Down, RP, is Low. The
power consumption is reduced to the Power-Down
level, IDD2, and the outputs are high impedance,
independent of Chip Enable, Output Enable or
Write Enable.
Standby.
Standby disables most of the internal
circuitry, allowing a substantial reduction of the
current consumption. The memory is in standby
when Chip Enable is at VIH. The power consump-
tion is reduced to the standby level IDD1 and the
outputs are set to high impedance, independently
from the Output Enable or Write Enable inputs.
If Chip Enable switches to VIH during a program or
erase operation, the device enters Standby mode
when finished.
Table 2. Bus Operations

Note:1. X = Don’t Care VIL or VIH. Depends on G
M58LW064C
READ MODES

Read operations can be performed in two different
ways depending on the settings in the Configura-
tion Register. If the clock signal is ‘don’t care’ for
the data output, the read operation is asynchro-
nous; if the data output is synchronized with clock,
the read operation is synchronous.
The read mode and format of the data output are
determined by the Configuration Register. (See
Configuration Register section for details).
On Power-up or after a Hardware Reset the mem-
ory defaults to Asynchronous Read mode.
Asynchronous Read Modes

In Asynchronous Read operations the clock signal
is ‘don’t care’. The device outputs the data corre-
sponding to the address latched, that is the mem-
ory array, Status Register, Common Flash
Interface, Electronic Signature or Block Protection
Status depending on the command issued. CR15
in the Configuration Register must be set to ‘1’ for
asynchronous operations.
During Asynchronous Read operations, if the bus
is inactive for a time equivalent to tAVQV, the de-
vice automatically enters Auto Low Power mode.
In this mode the internal supply current is reduced
to the Auto Low Power supply current, IDD5. The
Data Inputs/Outputs will still output data if a Bus
Read operation is in progress.
Automatic Low Power is only available in Asyn-
chronous Read modes.
Asynchronous Read operations can be performed
in three different ways, Asynchronous Latch Con-
trolled Read, Asynchronous Random Read and
Asynchronous Page Read.
Asynchronous Latch Controlled Read.

In Asynchronous Latch Controlled Read opera-
tions read the address is latched in the memory
before the value is output on the data bus, allowing
the address to change during the cycle without af-
fecting the address that the memory uses.
A valid bus operation involves setting the desired
address on the Address Inputs, setting Chip En-
able and Latch Enable Low, VIL and keeping Write
Enable High, VIH; the address is latched on the ris-
ing edge of Address Latch. Once latched, the Ad-
dress Inputs can change. Set Output Enable Low,
VIL, to read the data on the Data Inputs/Outputs.
See Figure 12., Asynchronous Latch Controlled
Read AC Waveforms, and Table
16., Asynchronous Latch Controlled Read AC
Characteristics, for details.
Asynchronous Random Read.
As the Latch En-
able input is transparent when set Low, VIL, Asyn-
chronous Random Read operations can be
performed by holding Latch Enable Low, VIL
throughout the bus operation.
See Figure 11., Asynchronous Random Read AC
Waveforms, and Table 15., Asynchronous Ran-
dom Read AC Characteristics., for details.
Asynchronous Page Read.
In Asynchronous
Page Read mode a Page of data is internally read
and stored in a Page Buffer. Each memory page is
4 Words and has the same A3-A22, only A1 and
A2 may change.
The first read operation within the Page has the
normal access time (tAVQV), subsequent reads
within the same Page have much shorter access
times (tAVQV1). If the Page changes then the nor-
mal, longer timings apply again.
See Figure 13., Asynchronous Page Read AC
Waveforms, and Table 17., Asynchronous Page
Read AC Characteristics, for details.
Synchronous Read Modes

In Synchronous Read mode the data output is syn-
chronized with the clock. CR15 in the Configura-
tion Register must be set to ‘0’ for synchronous
operations.
Synchronous Burst Read.
In Synchronous
Burst Read mode the data is output in bursts syn-
chronized with the clock. It is possible to perform
burst reads across bank boundaries.
Synchronous Burst Read mode can only be used
to read the memory array. For other read opera-
tions, such as Read Status Register, Read CFI,
Read Electronic Signature and Block Protection
Status, Single Synchronous Read or Asynchro-
nous Read must be used.
In Synchronous Burst Read mode the flow of the
data output depends on parameters that are con-
figured in the Configuration Register.
A valid Synchronous Burst Read operation begins
when the address is set on the Address Inputs,
Write Enable is High, VIH, and Chip Enable and
Latch Enable are Low, VIL, during the active edge
of the Clock. The address is latched on the first ac-
tive clock edge when Latch Enable is low, or on
the rising edge of Latch Enable, whichever occurs
first. The data becomes available for output after
the X-latency specified in the Burst Control Regis-
ter has expired. The output buffers are activated
by setting Output Enable Low, VIL. See Figures 6
and 7 for examples of Synchronous Burst Read
operations.
The number of Words to be output during a Syn-
chronous Burst Read operation can be configured
as 4 Words, 8 Words or Continuous (Burst Length
bits CR2-CR0). In Synchronous Continuous Burst
Read mode one Burst Read operation can access
the entire memory sequentially. If the starting ad-
dress is not associated with a page (4 Word)
boundary the Valid Data Ready, R, output goes
15/61
M58LW064C

Low, VIL, to indicate that the data will not be ready
in time and additional wait-states are required. The
Valid Data Ready output timing (bit CR8) can be
changed in the Configuration Register.
The order of the data output can be modified
through the Burst Type bit in the Configuration
Register. The burst sequence can be sequential or
interleaved.
See Table 20., Synchronous Burst Read AC Char-
acteristics, and Figure 18 and 19, Synchronous
Burst Read AC Waveform for details.
Single Synchronous Read.
Single Synchro-
nous Read operations are similar to Synchronous
Burst Read operations except that only the first
data output after the X latency is valid. Single Syn-
chronous Reads are used to read the Status Reg-
ister, CFI, Electronic Signature and Block
Protection Status.
M58LW064C
CONFIGURATION REGISTER

The Configuration Register is used to configure
the type of bus access that the memory will per-
form. The Configuration Register bits are de-
scribed in Table 3. They specify the selection of
the burst length, burst type, burst X and Y laten-
cies and the read operation. See figures 6 and 7
for examples of Synchronous Burst Read configu-
rations.
The Configuration Register is set through the
Command Interface and will retain its information
until it is re-configured, the device is reset, or the
device goes into Reset/Power-Down mode. The
Configuration Register is read using the Read
Electronic Signature Command at address 05h.
Read Select Bit (CR15).
The Read Select bit,
CR15, is used to switch between asynchronous
and synchronous read operations. When the Read
Select bit is set to ’1’, read operations are asyn-
chronous; when the Read Select but is set to ’0’,
read operations are synchronous.
On reset or power-up the Read Select bit is set to
’1’ for asynchronous access.
X-Latency Bits (CR13-CR11).
The X-Latency
bits are used during Synchronous read operations
to set the number of clock cycles between the ad-
dress being latched and the first data becoming
available. For correct operation the X-Latency bits
can only assume the values in Table
3., Configuration Register.
Internal Clock Divider Bit (CR10).
The Internal
Clock Divider Bit is used to divide the internal clock
by two. When CR10 is set to ‘1’ the internal clock
is divided by two, which effectively means that the
X and Y-Latency values are multiplied by two, that
is the number of clock cycles between the address
being latched and the first data becoming avail-
able will be twice the value set in CR13-CR11, and
the number of clock cycles between consecutive
reads will be twice the value set in CR9. For exam-
ple 8-1-1-1 will become 16-2-2-2. When CR10 is
set to ‘0’ the internal clock runs normally and the X
and Y-Latency values are those set in CR13-CR11
and CR9.
Y-Latency Bit (CR9).
The Y-Latency bit is used
during synchronous read operations to set the
number of clock cycles between consecutive
reads. The Y-Latency value depends on both the
X-Latency value and the setting in CR9.
When the Y-Latency is 1 the data changes each
clock cycle; when the Y-Latency is 2 the data
changes every second clock cycle. See Table
3., Configuration Register for valid combinations
of the Y-Latency, the X-Latency and the Clock fre-
quency.
Valid Data Ready Bit (CR8).
The Valid Data
Ready bit controls the timing of the Valid Data
Ready output pin, R. When the Valid Data Ready
bit is ’0’ the Valid Data Ready output pin is driven
Low for the active clock edge when invalid data is
output on the bus. When the Valid Data Ready bit
is ’1’ the Valid Data Ready output pin is driven Low
one clock cycle prior to invalid data being output
on the bus.
Burst Type Bit (CR7).
The Burst Type bit is used
to configure the sequence of addresses read as
sequential or interleaved. When the Burst Type bit
is ’0’ the memory outputs from interleaved ad-
dresses; when the Burst Type bit is ’1’ the memory
outputs from sequential addresses. See Table
4., Burst Type Definition, for the sequence of ad-
dresses output from a given starting address in
each mode.
Valid Clock Edge Bit (CR6).
The Valid Clock
Edge bit, CR6, is used to configure the active edge
of the Clock, K, during Synchronous Burst Read
operations. When the Valid Clock Edge bit is ’0’
the falling edge of the Clock is the active edge;
when the Valid Clock Edge bit is ’1’ the rising edge
of the Clock is active.
Burst Length Bit (CR2-CR0).
The Burst Length
bits set the maximum number of Words that can
be output during a Synchronous Burst Read oper-
ation.
Table 3., Configuration Register gives the valid
combinations of the Burst Length bits that the
memory accepts; Table 4., Burst Type Definition,
give the sequence of addresses output from a giv-
en starting address for each length.
CR5, CR4 and CR3 are reserved for future use.
17/61
M58LW064C
Table 3. Configuration Register

Note:1. 4 - 2 - 2 - 2 (represents X-Y-Y-Y) is not allowed. X latencies can be calculated as: (tAVQV – tLLKH + tQVKH) + tSYSTEM MARGIN < (X -1) tK. (X is an integer number from 4 to 8 and tK
is the clock period). Y latencies can be calculated as: tKHQV + tSYSTEM MARGIN + tQVKH < Y tK. tSYSTEM MARGIN is the time margin required for the calculation.
M58LW064C
19/61
M58LW064C
M58LW064C
COMMAND INTERFACE

All Bus Write operations to the memory are inter-
preted by the Command Interface. Commands
consist of one or more sequential Bus Write oper-
ations. The Commands are summarized in Table
5., Commands. Refer to Table 5 in conjunction
with the text descriptions below.
After power-up or a Reset operation the memory
enters Read mode.
Synchronous Read operations and Latch Con-
trolled Read operations can only be used to read
the memory array. The Electronic Signature, CFI
or Status Register will be read in asynchronous
mode or single synchronous burst mode. Once the
memory returns to Read Memory Array mode the
bus will resume the setting in the Configuration
Register automatically.
Read Memory Array Command.
The Read Mem-
ory Array command returns the memory to Read
mode. One Bus Write cycle is required to issue the
Read Memory Array command and return the
memory to Read mode. Once the command is is-
sued the memory remains in Read mode until an-
other command is issued. In Read mode Bus
Read operations access the memory array.
While the Program/Erase Controller is executing a
Program, Erase, Block Protect, Blocks Unprotect
or Protection Register Program operation the
memory will not accept the Read Memory Array
command until the operation completes.
Read Electronic Signature Command.
The Read
Electronic Signature command is used to read the
Manufacturer Code, the Device Code, the Block
Protection Status, the Configuration Register and
the Protection Register. One Bus Write cycle is re-
quired to issue the Read Electronic Signature
command. Once the command is issued subse-
quent Bus Read operations read the Manufacturer
Code, the Device Code, the Block Protection Sta-
tus, the Configuration Register or the Protection
Register until another command is issued. Refer to
Table 7., Read Electronic Signature, Table
3., Configuration Register and Figure
8., Protection Register Memory Map for informa-
tion on the addresses.
Read Query Command.
The Read Query Com-
mand is used to read data from the Common Flash
Interface (CFI) Memory Area. One Bus Write cycle
is required to issue the Read Query Command.
Once the command is issued subsequent Bus
Read operations read from the Common Flash In-
terface Memory Area. See Appendix B, Tables 26,
27, 28, 29, 30 and 31 for details on the information
contained in the Common Flash Interface (CFI)
memory area.
Read Status Register Command.
The Read Sta-
tus Register command is used to read the Status
Register. One Bus Write cycle is required to issue
the Read Status Register command. Once the
command is issued subsequent Bus Read opera-
tions read the Status Register until another com-
mand is issued.
The Status Register information is present on the
output data bus (DQ1-DQ7) when both Chip En-
able and Output Enable are low, VIL.
See the section on the Status Register and Table
10 for details on the definitions of the Status Reg-
ister bits
Clear Status Register Command.
The Clear Sta-
tus Register command can be used to reset bits 1,
3, 4 and 5 in the Status Register to ‘0’. One Bus
Write is required to issue the Clear Status Register
command.
The bits in the Status Register are sticky and do
not automatically return to ‘0’ when a new Write to
Buffer and Program, Erase, Block Protect, Block
Unprotect or Protection Register Program com-
mand is issued. If any error occurs then it is essen-
tial to clear any error bits in the Status Register by
issuing the Clear Status Register command before
attempting a new Program, Erase or Resume
command.
Block Erase Command.
The Block Erase com-
mand can be used to erase a block. It sets all of
the bits in the block to ‘1’. All previous data in the
block is lost. If the block is protected then the
erase operation will abort, the data in the block will
not be changed and the Status Register will output
the error.
Two Bus Write operations are required to issue the
command; the second Bus Write cycle latches the
block address in the internal state machine and
starts the Program/Erase Controller. Once the
command is issued subsequent Bus Read opera-
tions read the Status Register. See the section on
the Status Register for details on the definitions of
the Status Register bits.
During the erase operation the memory will only
accept the Read Status Register command and
the Program/Erase Suspend command. All other
commands will be ignored. Typical Erase times
are given in Table 9.
See Appendix C, Figure 25., Erase Flowchart and
Pseudo Code, for a suggested flowchart on using
the Block Erase command.
Word Program Command.
The Word Program
command is used to program a single word in the
memory array. Two Bus Write operations are re-
quired to issue the command; the first write cycle
sets up the Word Program command, the second
write cycle latches the address and data to be pro-
21/61
M58LW064C

grammed in the internal state machine and starts
the Program/Erase Controller.
If the block being programmed is protected an er-
ror will be set in the Status Register and the oper-
ation will abort without affecting the data in the
memory array. The block must be unprotected us-
ing the Blocks Unprotect command.
Write to Buffer and Program Command.
The
Write to Buffer and Program command is used to
program the memory array.
Up to 16 Words can be loaded into the Write Buffer
and programmed into the memory. Each Write
Buffer has the same A5-A22 addresses.
Four successive steps are required to issue the
command. One Bus Write operation is required to set up
the Write to Buffer and Program Command.
Issue the set up command with the selected
memory Block Address where the program
operation should occur (any address in the
block where the values will be programmed
can be used). Any Bus Read operations will
start to output the Status Register after the 1st
cycle. Use one Bus Write operation to write the same
block address along with the value N on the
Data Inputs/Output, where N+1 is the number
of Words to be programmed. Use N+1 Bus Write operations to load the
address and data for each Word into the Write
Buffer. See the constraints on the address
combinations listed below. The addresses
must have the same A5-A22. Finally, use one Bus Write operation to issue
the final cycle to confirm the command and
start the Program operation.
Invalid address combinations or failing to follow
the correct sequence of Bus Write cycles will set
an error in the Status Register and abort the oper-
ation without affecting the data in the memory ar-
ray. The Status Register should be cleared before
re-issuing the command.
If the block being programmed is protected an er-
ror will be set in the Status Register and the oper-
ation will abort without affecting the data in the
memory array. The block must be unprotected us-
ing the Blocks Unprotect command.
See Appendix C, Figure 23., Write to Buffer and
Program Flowchart and Pseudo Code, for a sug-
gested flowchart on using the Write to Buffer and
Program command.
Program/Erase Suspend Command.
The Pro-
gram/Erase Suspend command is used to pause a
Word Program, Write to Buffer and program or
erase operation. The command will only be ac-
cepted during a program or an erase operation. It
can be issued at any time during an erase opera-
tion but will only be accepted during a Word Pro-
gram or Write to Buffer and Program command if
the Program/Erase Controller is running.
One Bus Write cycle is required to issue the Pro-
gram/Erase Suspend command and pause the
Program/Erase Controller. Once the command is
issued it is necessary to poll the Program/Erase
Controller Status bit (SR7) to find out when the
Program/Erase Controller has paused; no other
commands will be accepted until the Program/
Erase Controller has paused. After the Program/
Erase Controller has paused, the memory will con-
tinue to output the Status Register until another
command is issued.
During the polling period between issuing the Pro-
gram/Erase Suspend command and the Program/
Erase Controller pausing it is possible for the op-
eration to complete. Once the Program/Erase
Controller Status bit (SR7) indicates that the Pro-
gram/Erase Controller is no longer active, the Pro-
gram Suspend Status bit (SR2) or the Erase
Suspend Status bit (SR6) can be used to deter-
mine if the operation has completed or is suspend-
ed. For timing on the delay between issuing the
Program/Erase Suspend command and the Pro-
gram/Erase Controller pausing see Table 9.
During Program/Erase Suspend the Read Memo-
ry Array, Read Status Register, Read Electronic
Signature, Read Query and Program/Erase Re-
sume commands will be accepted by the Com-
mand Interface. Additionally, if the suspended
operation was erase then the Write to Buffer and
Program, and the Program Suspend commands
will also be accepted. When a program operation
is completed inside a Block Erase Suspend the
Read Memory Array command must be issued to
reset the device in Read mode, then the Erase Re-
sume command can be issued to complete the
whole sequence. Only the blocks not being erased
may be read or programmed correctly.
See Appendix C, Figure 24., Program Suspend &
Resume Flowchart and Pseudo Code, and Figure
26., Erase Suspend & Resume Flowchart and
Pseudo Code, for suggested flowcharts on using
the Program/Erase Suspend command.
Program/Erase Resume Command.
The Pro-
gram/Erase Resume command can be used to re-
start the Program/Erase Controller after a
Program/Erase Suspend operation has paused it.
One Bus Write cycle is required to issue the Pro-
gram/Erase Resume command. Once the com-
mand is issued subsequent Bus Read operations
read the Status Register.
Set Configuration Register Command.
The
Set Configuration Register command is used to
write a new value to the Configuration Register
which defines the burst length, type, X and Y laten-
M58LW064C
cies, Synchronous/Asynchronous Read mode and
the valid Clock edge configuration.
Two Bus Write cycles are required to issue the Set
Configuration Register command. Once the com-
mand is issued the memory returns to Read mode
as if a Read Memory Array command had been is-
sued.
The value for the Configuration Register is pre-
sented on A1-A16. CR0 is on A1, CR1 on A2, etc.;
the other address bits are ignored.
Block Protect Command.
The Block Protect
command is used to protect a block and prevent
program or erase operations from changing the
data in it. Two Bus Write cycles are required to is-
sue the Block Protect command; the second Bus
Write cycle latches the block address in the inter-
nal state machine and starts the Program/Erase
Controller. Once the command is issued subse-
quent Bus Read operations read the Status Reg-
ister. See the section on the Status Register for
details on the definitions of the Status Register
bits.
During the Block Protect operation the memory will
only accept the Read Status Register command.
All other commands will be ignored. Typical Block
Protection times are given in Table 9.
The Block Protection bits are non-volatile, once
set they remain set through reset and power-
down/power-up. They are cleared by a Blocks Un-
protect command.
See Appendix C, Figure 27., Block Protect Flow-
chart and Pseudo Code, for a suggested flowchart
on using the Block Protect command.
Blocks Unprotect Command.
The Blocks Un-
protect command is used to unprotect all of the
blocks. Two Bus Write cycles are required to issue
the Blocks Unprotect command; the second Bus
Write cycle starts the Program/Erase Controller.
Once the command is issued subsequent Bus
Read operations read the Status Register. See the
section on the Status Register for details on the
definitions of the Status Register bits.
During the Block Unprotect operation the memory
will only accept the Read Status Register com-
mand. All other commands will be ignored. Typical
Block Protection times are given in Table 9.
See Appendix C, Figure 28., Block Unprotect
Flowchart and Pseudo Code, for a suggested flow-
chart on using the Block Unprotect command.
Protection Register Program Command.
The
Protection Register Program command is used to
Program the 64 bit user segment of the Protection
Register. The segment is programmed 16 bits at a
time. Two write cycles are required to issue the
Protection Register Program command. The first bus cycle sets up the Protection
Register Program command. The second latches the Address and the Data
to be written to the Protection Register and
starts the Program/Erase Controller.
Read operations output the Status Register con-
tent after the programming has started.
The user-programmable segment can be locked
by programming bit 1 of the Protection Register
Lock location to ‘0’ (see Table 8). Bit 0 of the Pro-
tection Register Lock location locks the factory
programmed segment and is programmed to ‘0’ in
the factory. The locking of the Protection Register
is not reversible, once the lock bits are pro-
grammed no further changes can be made to the
values stored in the Protection Register, see Fig-
ure 8., Protection Register Memory Map. Attempt-
ing to program a previously protected Protection
Register will result in a Status Register error.
The Protection Register Program cannot be sus-
pended. See Appendix C, Figure 29., Protection
Register Program Flowchart and Pseudo Code,
for the flowchart for using the Protection Register
Program command.
Configure STS Command.

The Configure STS command is used to configure
the Status/(Ready/Busy) pin. After power-up or re-
set the STS pin is configured in Ready/Busy
mode. The pin can be configured in Status mode
using the Configure STS command (refer to Sta-
tus/(Ready/Busy) section for more details.
Two write cycles are required to issue the Config-
ure STS command. The first bus cycle sets up the Configure STS
command. The second specifies one of the four possible
configurations (refer to Table 6., Configuration
Codes): Ready/Busy mode Pulse on Erase complete mode Pulse on Program complete mode Pulse on Erase or Program complete
mode
The device will not accept the Configure STS com-
mand while the Program/Erase controller is busy
or during Program/Erase Suspend. When STS pin
is pulsing it remains Low for a typical time of
250ns. Any invalid Configuration Code will set an
error in the Status Register.
23/61
M58LW064C
Table 5. Commands

Note:1. X Don’t Care; RA Read Address, RD Read Data, IDA Identifier Address, IDD Identifier Data, SRD Status Register Data, PA Program
Address; PD Program Data, QA Query Address, QD Query Data, BA Any address in the Block, CR Configuration Register value,
CC Configuration Code. Base Address, refer to Figure 8 and Table 8 for more information. For Identifier addresses and data refer to Table 7., Read Electronic Signature. For Query Address and Data refer to APPENDIX B., COMMON FLASH INTERFACE - CFI.
Table 6. Configuration Codes

Note:1. DQ2-DQ7 are reserved When STS pin is pulsing it remains Low for a typical time of 250ns.
M58LW064C
25/61
M58LW064C
Table 9. Program, Erase Times and Program Erase Endurance Cycles

Note:1. Typical values measured at room temperature and nominal voltages. Sampled, but not 100% tested. Effective byte programming time 6µs, effective word programming time 12µs. Maximum value measured at worst case conditions for both temperature and VDD after 100,000 program/erase cycles. Maximum value measured at worst case conditions for both temperature and VDD.
M58LW064C
STATUS REGISTER

The Status Register provides information on the
current or previous Program, Erase, Block Protect
or Blocks Unprotect operation. The various bits in
the Status Register convey information and errors
on the operation. They are output on DQ7-DQ0.
To read the Status Register the Read Status Reg-
ister command can be issued. The Status Register
is automatically read after Program, Erase, Block
Protect, Blocks Unprotect and Program/Erase Re-
sume commands. The Status Register can be
read from any address.
The Status Register can only be read using Asyn-
chronous Bus Read or Single Synchronous Read
operations. Once the memory returns to Read
Memory Array mode the bus will resume the set-
ting in the Configuration Register automatically.
The contents of the Status Register can be updat-
ed during an erase or program operation by tog-
gling the Output Enable pin or by dis-activating
(Chip Enable, VIH) and then reactivating (Chip En-
able and Output Enable, VIL) the device.
Status Register bits SR5, SR4, SR3 and SR1 are
associated with various error conditions and can
only be reset with the Clear Status Register com-
mand. The Status Register bits are summarized in
Table 10., Status Register Bits. Refer to Table 10
in conjunction with the following text descriptions.
Program/Erase Controller Status Bit (SR7).
The
Program/Erase Controller Status bit indicates
whether the Program/Erase Controller is active or
inactive. When the Program/Erase Controller Sta-
tus bit is Low, VOL, the Program/Erase Controller
is active and all other Status Register bits are High
Impedance; when the bit is High, VOH, the Pro-
gram/Erase Controller is inactive.
The Program/Erase Controller Status is Low im-
mediately after a Program/Erase Suspend com-
mand is issued until the Program/Erase Controller
pauses. After the Program/Erase Controller paus-
es the bit is High.
During Program, Erase, Block Protect and Blocks
Unprotect operations the Program/Erase Control-
ler Status bit can be polled to find the end of the
operation. The other bits in the Status Register
should not be tested until the Program/Erase Con-
troller completes the operation and the bit is High.
After the Program/Erase Controller completes its
operation the Erase Status, Program Status and
Block Protection Status bits should be tested for
errors.
Erase Suspend Status Bit (SR6).
The Erase
Suspend Status bit indicates that an erase opera-
tion has been suspended and is waiting to be re-
sumed. The Erase Suspend Status should only be
considered valid when the Program/Erase Con-
troller Status bit is High (Program/Erase Controller
inactive); after a Program/Erase Suspend com-
mand is issued the memory may still complete the
operation rather than entering the Suspend mode.
When the Erase Suspend Status bit is Low, VOL,
the Program/Erase Controller is active or has com-
pleted its operation. When the bit is High, VOH, a
Program/Erase Suspend command has been is-
sued and the memory is waiting for a Program/
Erase Resume command.
When a Program/Erase Resume command is is-
sued the Erase Suspend Status bit returns Low.
Erase Status Bit (SR5).
The Erase Status bit
can be used to identify if the memory has failed to
verify that the block has erased correctly or that all
blocks have been unprotected successfully. The
Erase Status bit should be read once the Program/
Erase Controller Status bit is High (Program/Erase
Controller inactive).
When the Erase Status bit is Low, VOL, the mem-
ory has successfully verified that the block has
erased correctly or all blocks have been unprotect-
ed successfully. When the Erase Status bit is
High, VOH, the erase operation has failed. De-
pending on the cause of the failure other Status
Register bits may also be set to High, VOH. If only the Erase Status bit (SR5) is set High,
VOH, then the Program/Erase Controller has
applied the maximum number of pulses to the
block and still failed to verify that the block has
erased correctly or that all the blocks have
been unprotected successfully. If the failure is due to an erase or blocks
unprotect with VPEN low, VOL, then VPEN
Status bit (SR3) is also set High, VOH. If the failure is due to an erase on a protected
block then Block Protection Status bit (SR1) is
also set High, VOH. If the failure is due to a program or erase
incorrect command sequence then Program
Status bit (SR4) is also set High, VOH.
Once set High, the Erase Status bit can only be re-
set Low by a Clear Status Register command or a
hardware reset. If set High it should be reset be-
fore a new program or erase command is issued,
otherwise the new command will appear to fail.
Program Status Bit (SR4).
The Program Status
bit is used to identify a Program or Block Protect
failure. The Program Status bit should be read
once the Program/Erase Controller Status bit is
High (Program/Erase Controller inactive).
When the Program Status bit is Low, VOL, the
memory has successfully verified that the Write
Buffer has programmed correctly or the block is
protected. When the Program Status bit is High,
27/61
M58LW064C

VOH, the program or block protect operation has
failed. Depending on the cause of the failure other
Status Register bits may also be set to High, VOH. If only the Program Status bit (SR4) is set
High, VOH, then the Program/Erase Controller
has applied the maximum number of pulses to
the byte and still failed to verify that the Write
Buffer has programmed correctly or that the
Block is protected. If the failure is due to a program or block
protect with VPEN low, VOL, then VPEN Status
bit (SR3) is also set High, VOH. If the failure is due to a program on a protected
block then Block Protection Status bit (SR1) is
also set High, VOH. If the failure is due to a program or erase
incorrect command sequence then Erase
Status bit (SR5) is also set High, VOH.
Once set High, the Program Status bit can only be
reset Low by a Clear Status Register command or
a hardware reset. If set High it should be reset be-
fore a new program or erase command is issued,
otherwise the new command will appear to fail.
VPEN Status Bit (SR3).
The VPEN Status bit can
be used to identify if a Program, Erase, Block Pro-
tection or Block Unprotection operation has been
attempted when VPEN is Low, VIL.
When the VPEN Status bit is Low, VOL, no Pro-
gram, Erase, Block Protection or Block Unprotec-
tion operations have been attempted with VPEN
Low, VIL, since the last Clear Status Register com-
mand, or hardware reset. When the VPEN Status
bit is High, VOH, a Program, Erase, Block Protec-
tion or Block Unprotection operation has been at-
tempted with VPEN Low, VIL.
Once set High, the VPEN Status bit can only be re-
set by a Clear Status Register command or a hard-
ware reset. If set High it should be reset before a
new Program, Erase, Block Protection or Block
Unprotection command is issued, otherwise the
new command will appear to fail.
Program Suspend Status Bit (SR2).
The Pro-
gram Suspend Status bit indicates that a Program
operation has been suspended and is waiting to
be resumed. The Program Suspend Status should
only be considered valid when the Program/Erase
Controller Status bit is High (Program/Erase Con-
troller inactive); after a Program/Erase Suspend
command is issued the memory may still complete
the operation rather than entering the Suspend
mode.
When the Program Suspend Status bit is Low,
VOL, the Program/Erase Controller is active or has
completed its operation; when the bit is High, VOH,
a Program/Erase Suspend command has been is-
sued and the memory is waiting for a Program/
Erase Resume command.
When a Program/Erase Resume command is is-
sued the Program Suspend Status bit returns Low.
Block Protection Status Bit (SR1).
The Block
Protection Status bit can be used to identify if a
program or erase operation has tried to modify the
contents of a protected block.
When the Block Protection Status bit is Low, VOL,
no program or erase operations have been at-
tempted to protected blocks since the last Clear
Status Register command or hardware reset.
When the Block Protection Status bit is High, VOH,
a program (SR4 set High) or erase (SR5 set High)
operation has been attempted on a protected
block.
Once set High, the Block Protection Status bit can
only be reset Low by a Clear Status Register com-
mand or a hardware reset. If set High it should be
reset before a new program or erase command is
issued, otherwise the new command will appear to
fail.
Reserved (SR0).
SR0 of the Status Register is
reserved. Its value should be masked.
M58LW064C
Table 10. Status Register Bits
29/61
M58LW064C
MAXIMUM RATING

Stressing the device above the ratings listed in Ta-
ble 11., Absolute Maximum Ratings, may cause
permanent damage to the device. These are
stress ratings only and operation of the device at
these or any other conditions above those indicat-
ed in the Operating sections of this specification is
not implied. Exposure to Absolute Maximum Rat-
ing conditions for extended periods may affect de-
vice reliability. Refer also to the
STMicroelectronics SURE Program and other rel-
evant quality documents.
Table 11. Absolute Maximum Ratings

Note:1. Compliant with the JEDEC Std J-STD-020B (for small body, Sn-Pb or Pb assermbly), the ST ECOPACK® 7191395 specification,
and the European directive on Restrictions on Hazardous Substances (RoHS) 2002/95/EU.
M58LW064C
DC AND AC PARAMETERS

This section summarizes the operating and mea-
surement conditions, and the DC and AC charac-
teristics of the device. The parameters in the DC
and AC characteristics Tables that follow, are de-
rived from tests performed under the Measure-
ment Conditions summarized in Table
12., Operating and AC Measurement Conditions.
Designers should check that the operating condi-
tions in their circuit match the measurement condi-
tions when relying on the quoted parameters.
Table 12. Operating and AC Measurement Conditions
Table 13. Capacitance

Note:1. TA = 25°C, f = 1 MHz Sampled only, not 100% tested.
31/61
M58LW064C
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED