IC Phoenix
 
Home ›  LL6 > L93PI,QUAD LOW SIDE DRIVER
L93PI Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
L93PISTN/a5000avaiQUAD LOW SIDE DRIVER


L93PI ,QUAD LOW SIDE DRIVERABSOLUTE MAXIMUM RATINGS (no damage or latch)Symbol Parameter Value UnitV Supply voltage -24 to 45 ..
L9407F ,CAR ALTERNATOR VOLTAGE REGULATORL9407FCAR ALTERNATOR VOLTAGE REGULATORPRODUCT PREVIEW■ FULLY MONOLITHIC DESIGN■ LOW SIDE FIELD DRIV ..
L9468 ,Alternator voltage regulator with protected diagnostic lamp driverAbsolute Maximum RatingsSymbol Parameter Value UnitV Thermal Supply Voltage (load dump) 40 VSI Outp ..
L9468N ,Alternator voltage regulator with protected diagnostic lamp driverFeatures■ FULLY MONOLITHIC DESIGN■ HIGH SIDE FIELD DRIVE■ THERMAL PROTECTION■ FIELD DRIVER SHORT CI ..
L9473 ,CAR ALTERNATOR VOLTAGE REGULATORBlock DiagramNTC4 178263Rev. 1May 2005 1/9L9473 Table 2. PIN DESCRIPTIONN° Pin Description1V Gener ..
L9474 , ALL SILICON VOLTAGE REGULATOR
LC73872 ,DTMF ReceiverFeatures u d. Detects all 16 DTMF signals. -"i1"1-'un I-; T. Includes on-chip all filters required ..
LC73872 ,DTMF ReceiverFeatures u d. Detects all 16 DTMF signals. -"i1"1-'un I-; T. Includes on-chip all filters required ..
LC73872 ,DTMF ReceiverOrdering number : EN4998CMOS ICLC73872MDTMF ReceiverOverview Package DimensionsThe LC73872M is a DT ..
LC73872M ,DTMF ReceiverFeatures u d. Detects all 16 DTMF signals. -"i1"1-'un I-; T. Includes on-chip all filters required ..
LC7387M , DTMF ReceiverElectrical Characteristics at Ta = 25°C, VDD = 5 V, vss = 0 V, fosc = 4.194304 MHz, _ Ratings _Para ..
LC73881M ,DTMF Receiver LSIElectrical Characteristics at Ta = 25°C, V = 3 V, V = 0 V, f = 4.194304 MHzDD SS OSCParameter Symbo ..


L93PI
QUAD LOW SIDE DRIVER
L93PI
QUAD LOW SIDE DRIVER
WIDE INPUT VOLTAGE RANGE -24V UP TO +45V
WIDE OPERATING SUPPLY VOLTAGE
RANGE FROM 4.5V UP TO 32V
REVERSE BIASING PROTECTED (VS = -24V)
VERY LOW STANDBY QUIESCENT CUR-
RENT < 2μA
PROGRAMMABLE SIGNAL TRANSFER PO-
LARITY
TTL AND CMOS COMPATIBLE INPUTS
DEFINED OUTPUT OFF STATE OFF FOR
OPEN INPUTS
FOUR OPEN DRAIN DMOS OUTPUTS, WITH
RDSon = 1.5 Ω at 25°C and VS > 6V
OUTPUT CURRENT LIMITATION
CONTROLLED OUTPUT SLOPE FOR LOW EMI
OVERTEMPERATURE SHUT-DOWN
INTEGRATED OUTPUT CLAMPING FOR
FAST INDUCTIVE RECIRCULATION VFB > 45V
STATUS MONITORING FOR
- OVERTEMPERATURE
- DISCONNECTED GROUND OR SUPPLY
VOLTAGE
ESD: ALL PINS ARE GUARANTEED TILL 2kV
HUMAN BODY MODEL
DESCRIPTION

The L93PI is a monolithic integrated quad low
side driver realized in advanced Multipower-BCD
technology. It is intended to drive lines, lamps or
relais in automotive or industrial applications.
BLOCK DIAGRAM
ABSOLUTE MAXIMUM RATINGS (no damage or latch)
PIN DESCRIPTION
PIN CONNECTION (Top view)
L93PI

2/8
THERMAL DATA
(1) See SGS-THOMSON Microelectronics databook:"Thermal Management in Surface Mount Technology"
(2) See SGS-THOMSON Microelectronics databook:"Thermal characteristics of SO20"
OPERATING CONDITIONS
(The electrical characteristics are valid within the below defined operating
ranges, unless otherwise specified. The function will be guaranted by design until TjMON switch-OFF-level.
ELECTRICAL CHARACTERISTICS (Refer to the test circuit, unless otherwise specified.)
L93PI

3/8
ELECTRICAL CHARACTERISTICS (Continued)
Figure 1
L93PI

4/8
CIRCUIT DESCRIPTION
The L93PI is a quad low side driver for lines,
lamps or inductive loads in automotive and indus-
trial applications.
All INputs are TTL or CMOS compatible. This al-
lows the device to be driven directly by a micro-
controller. For the noise immunity, all inputs have
a Schmitt-trigger with a hysteresis of typ. 100mV.
Each input stage has an input voltage protection
from -24V to 45V. The device can be activated
with a ’high’ signal on ENable input. ENable ’low’
switches the device into the sleep mode. In this
mode the quiescent current is less than 10μA. A
high signal on PRoGramming input changes the
signal transfer polarity from noninverting into the
inverting mode. Normally this pin is connected to
VS or GND. These pins (PRG and EN) are inter-
nally fixed at low status by open input condition.
Independent of the PRoGramming input, the
OUTput switches off, if the signal INput pin is not
connected.
Each output driver has a current limitation of min
0.4A and a seperate thermal shut-down. The ther-
mal shut-down deactivates that output which ex-
ceeds Temperature switch off level. About 20K
below this temperature threshold the output will
be activated again. This means, that each output
is able to sink continuously 285mA without acti-
vating thermal shut-down at 85°C ambient tem-
perature (SO20). The slew rate of the output is
limited to max. 14V/μs to reduce the electromag-
netic interference, but not for the enable transfer
characteristic (see fig. 1). An integrated active fly-
back voltage limitation clamps the output voltage
during the flyback phase of inductive loads to typ.
50V. The power DMOS switches ON, if the device
is enabled and the OUTput swings below ground.
This protection avoids the activation of parasitics
inside the power DMOS.
The DIAGnostic is an open drain output. The logic
status depends on the PRoGramming pin. If the
PRG pin is ’low’ the DIAG output becomes low, if
the device works correctly.
At thermal shut-down of one channel, discon-
nected ground or supply voltage the DIAGnostic
output becomes high. If the PRG pin is ’high’ this
output is switched off at normal function and
switched on at overtemperature.
DIAGNOSTIC TABLE

X = not relevant * selective for each channel at overtemperature
L93PI

5/8
Figure 2: Application circuit for inverting transfer polarity.
L93PI

6/8
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED