IC Phoenix
 
Home ›  EE4 > ESDA18-1F2,Transient Voltage Suppressor
ESDA18-1F2 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
ESDA18-1F2 |ESDA181F2STN/a7526avaiTransient Voltage Suppressor
ESDA18-1F2 |ESDA181F2ST ?N/a5129avaiTransient Voltage Suppressor


ESDA18-1F2 ,Transient Voltage SuppressorFEATURES AND BENEFITS:■ Stand-off voltage 16V■ Unidirectional device■ Low clamping factor V /VCL BR ..
ESDA18-1F2 ,Transient Voltage SuppressorPin Configuration (ball side)IEC61000-4-2Level 4 15kV (air discharge) 8kV (contact discharge)A B1K ..
ESDA18-1K ,EOS and ESD Transil™ protection for charger and battery portFeatures■ Breakdown voltage: 12 V, 18 V■ Unidirectional device■ High peak power dissipation: 450 W ..
ESDA19SC6 ,QUAD TRANSIL ARRAY FOR ESD PROTECTIONAPPLICATIONSWhere transient overvoltage protection in ESDsensitive equipment is required, such as : ..
ESDA25B1 ,TRANSIL ARRAY FOR ESD PROTECTIONFEATURESSO-86 BIDIRECTIONAL TRANSIL™ FUNCTIONSVERY LOW CAPACITANCE : C= 20 pF @ VRM150 W peak pulse ..
ESDA25B1RL ,TRANSIL ARRAY FOR ESD PROTECTIONFEATURESSO-86 BIDIRECTIONAL TRANSIL™ FUNCTIONSVERY LOW CAPACITANCE : C= 20 pF @ VRM150 W peak pulse ..
FA7617CN ,Bipolar IC for switching power supply controlFeatures1 4FA7610CP(N) 4.9• For flyback transformer-type or step-up power-supply circuit(maximum ou ..
FA7700V , For Switching Power Supply Control
FA7701V , For Switching Power Supply Control
FA7701V , For Switching Power Supply Control
FA7711V , FUJI Power Supply Control IC
FAB2210UCX , Audio Subsystem with Class-G Headphone and 3.3W Mono Class-D Speaker with Dynamic Range Compression


ESDA18-1F2
Transient Voltage Suppressor
1/7
ESDA18-1F2

TRANSIL™: Transient Voltage Suppressor
REV. 1May 2005
Figure 1: Pin Configuration (ball side)
Table 1: Order Code
FEATURES AND BENEFITS:
Stand-off voltage 16V Unidirectional device Low clamping factor VCL/VBR Fast response time Very thin package: 0.65 mm
DESCRIPTION

The ESDA18-1F2 is a single line Transil diode
designed specifically for the protection of
integrated circuits into portable equipment and
miniaturized electronics devices subject to ESD &
EOS transient overvoltages.
COMPLIES WITH THE FOLLOWING STANDARDS:
IEC61000-4-2

Level 4 15kV (air discharge)
8kV (contact discharge)
ASD
(Application Specific Devices)
TM: TRANSIL is a trademark of STMicroelectronics.
ESDA18-1F2
Table 2: Absolute Ratings (limiting value, per diode)
Table 3: Electrical Characteristics (T
amb = 25°C)
(1) 8 / 20 µs pulse waveform.
(2) DC current not recommended for more than 5 sec. Even if Transil failure mode is short circuit the bumps could exceed melting temper-

ature and the component disassembled from the board.
ESDA18-1F2
3/7
Figure 2: Relative variation of peak pulse
power versus initial junction temperature
Figure 3: Peak pulse power versus exponen-
tial pulse duration
Figure 4: Clamping voltage versus peak pulse
current (typical values, exponential waveform)
Figure 5: Forward voltage drop versus peak
forward current (typical values)
Figure 6: Junction capacitance versus reverse
voltage applied (typical values)
Figure 7: Relative variation of leakage current
versus junction temperature (typical values)
ESDA18-1F2
One major point is that the ESDA18-1F2 has to ensure the safety during reverse battery operation. Indeed,
during this operation the device must clamp the DC reverse voltage below 1.3V @ 0.85A (max current).
Thus reverse battery operation has been simulated by inverting the polatrity of the TRANSIL (please see
figures 8 and 9)
Figure 8: Reverse battery operation setup
Figure 9: Reverse battery operation results

A short calculation based on Reverse battery operation results figures clearly show that in such real phone
application the ESDA18-1F2 clamp the DC voltage below 1.3V.
Typically the ESDA18-1F2 can clamp the DC voltage @ 0.9V @0.76A DC current:DC max×----------------------- 21.4×
3.14----------------- 0.9V≈≈=DC max×--------------------- 21.2×
3.14----------------- 0.76A≈≈=
ESDA18-1F2
5/7
Figure 10: Ordering Information Scheme
Figure 12: Foot Print Recommendations Figure 13: Marking
ESDA18-1F2
Figure 14: FLIP-CHIP Tape and Reel Specification
Table 4: Ordering Information
Note: More packing informations are available in the application note

AN1235: “Flip-Chip: Package description and recommendations for use”
Table 5: Revision History
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED