IC Phoenix
 
Home ›  DD26 > DS1804-050-DS1804-100-DS1804U-010-DS1804X-010-DS1804Z-010-DS1804Z-100,NV Trimmer Potentiometer
DS1804-050-DS1804-100-DS1804U-010-DS1804X-010-DS1804Z-010 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
DS1804-050 |DS1804050DALLASN/a236avaiNV Trimmer Potentiometer
DS1804-100 |DS1804100DALLASN/a306avaiNV Trimmer Potentiometer
DS1804U-010 |DS1804U010MAXIMN/a2060avaiNV Trimmer Potentiometer
DS1804X-010 |DS1804X010DALLASN/a46avaiNV Trimmer Potentiometer
DS1804Z-010 |DS1804Z010DALLASN/a78avaiNV Trimmer Potentiometer
DS1804Z-100 |DS1804Z100DALLASN/a21avaiNV Trimmer Potentiometer


DS1804U-010 ,NV Trimmer Potentiometerapplications using a CPU or manual control inputwith minimal external circuitry. Wiper position of ..
DS1804U-010 ,NV Trimmer Potentiometerblock diagram of the DS1804 is shown in Figure 1.The three-terminal port of the DS1804 provides an ..
DS1804U-010/T&R ,Nonvolatile Trimmer Potentiometerblock diagram of the DS1804 is shown in Figure 1. The three-terminal port of the DS1804 provides a ..
DS1804U-050 ,NV Trimmer PotentiometerFEATURES PIN ASSIGNMENT Single 100-position taper potentiometer Nonvolatile (NV) on-demand wiper ..
DS1804UR-050 ,Nonvolatile Trimmer PotentiometerFEATURES PIN ASSIGNMENT  Single 100-Position Taper Potentiometer  Nonvolatile (NV) On-Demand ..
DS1804X-010 ,NV Trimmer Potentiometerapplications using a CPU or manual control inputwith minimal external circuitry. Wiper position of ..
DW025AF-M , DW025 Dual Output-Series Power Modules: dc-dc Converters 36 Vdc to 75 Vdc Input; Dual Outputs; 25 W
DWC010 ,Silicon Epitaxial Planar Type Ultrahigh-Speed Switching DiodeAbsolute Maximum Ratings at Ta = 25˚CPl arameter Ss ymbo Cs ondition Rt ating UniPV eak Reverse Vol ..
DWR-SJS-TU2-1 , Power LED
DXT3150-13 , NPN SURFACE MOUNT TRANSISTOR
DXT3904 , TECHNICAL SPECIFICATIONS OF NPN EPITAXIAL PLANAR TRANSISTOR
DXT3904-13 , NPN SURFACE MOUNT TRANSISTOR


DS1804-050-DS1804-100-DS1804U-010-DS1804X-010-DS1804Z-010-DS1804Z-100
NV Trimmer Potentiometer
FEATURESSingle 100-position taper potentiometerNonvolatile “on-demand” wiper storageOperates from 3V or 5V suppliesUp/down, increment-controlled interfaceAvailable in 8-pin (300-mil) DIP, 8-pin
(150-mil) SOIC, 8-pin (118-mil) µSOP, and
Flip Chip packagesOperating Temperature:Industrial:-40ºC to +85ºCStandard Resistance Values:DS1804-01010 kΩDS1804-05050 kΩDS1804-100100 kΩ
PIN ASSIGNMENT
PIN DESCIPTION
-High-Terminal of PotentiometerL - Low-Terminal of Potentiometer- Wiper of Potentiometer
VCC - 3V or 5V Power Supply- Chip SelectD - Up/Down Control
INC - Increment/Decrement Wiper ControlGND-Ground
DESCRIPTION

The DS1804 NV Trimmer Potentiometer is a nonvolatile digital potentiometer having 100 positions. The
device provides an ideal method for low-cost trimming applications using a CPU or manual control inputwith minimal external circuitry. Wiper position of the DS1804 can be stored in EEPROM memory on
demand. The device’s wiper position is manipulated by a 3-terminal port that provides an increment/
decrement counter controlled interface. This port consists of the control inputs CS, INC, and U/D. The
DS1804 is available in three resistor grades, which include a 10 kΩ, 50 kΩ, and 100 kΩ. The device is
provided in an industrial temperature grade. Additionally, the DS1804 will operate from 3V or 5Vsupplies and is ideal for portable application requirements. Three packaging options are available and
include the 8-pin (300-mil) DIP, 8-pin (150-mil) SOIC, 8-pin (118-mil) uSOP, and the Flip Chip
Package.
DS1804

8-Pin DIP (300-mil)8-Pin SOIC (150-mil)
8-Pin uSOP (118-mil)8-Pin Flip Chip Package
See Mech. Drawings Section
DS1804
OPERATION

The DS1804 is a single nonvolatile potentiometer. The device has a total of 100 tap-points including the
L- and H- terminals. A total of 99 resistive segments exist between the L- and H- terminals. These tap-
points are accessible to the W-terminal, whose position is controlled via a 3-terminal control port. A
block diagram of the DS1804 is shown in Figure 1.
The 3-terminal port of the DS1804 provides an increment/decrement interface which is activated via a
chip select input. This interface consists of the input signals CS, INC, and U/D. These input signals
control a 7-bit up/down counter. The output of the 7-bit up/down counter controls a 1 of 100 decoder to
select wiper position. Additionally, this interface provides for a wiper storage operation using the CSand
INC input control pins. The timing diagram for the 3-terminal interface control is shown in Figure 2.
PIN DESCRIPTIONS
VCC - Power Supply. The DS1804 will support supply voltages ranging from +2.7 to +5.5 volts.
GND - Ground.
H - High-Terminal Potentiometer. This is the high terminal of the potentiometer. It is not required that

this terminal be connected to a potential greater than the L-terminal. Voltage applied to the H-terminal
can not exceed the power-supply voltage, VCC, or go below ground.
L - Low-Terminal Potentiometer. This is the low terminal of the potentiometer. It is not required that this
terminal be connected to a potential less than the H-terminal. Voltage applied to the L-terminal cannot
exceed the power-supply voltage, VCC, or go below ground.
W - Wiper of the Potentiometer. This pin is the wiper of the potentiometer. Its position on the resistor

array is controlled by the 3-terminal control port. Voltage applied to the wiper cannot exceed the power-supply voltage, VCC, or go below ground. - Chip Select. The CS input is used to activate the control port of the DS1804. This input is active
low. When in a high-state, activity on the INC and U/D port pins will not affect or change wiper
position.
INC - Wiper Movement Control. This input provides for wiper position changes when the
CS pin is low.
Wiper position changes of the W-terminal will occur one position per high-to-low transition of this input
signal. Position changes will not occur if the CS pin is in a high state.D - Up/Down Control. This input sets the direction of wiper movement. When in a high state and CS
is low, any high-to-low transition on INC will cause a one position movement of the wiper towards the
H-terminal. When in a low state and CS is low, any high-to-low transitions on INC will cause the
position of the wiper to move towards the L-terminal.
DS1804
DS1804 BLOCK DIAGRAM Figure 1


POWER-UP/POWER-DOWN CONDITIONS

On power-up the DS1804 will load the value of EEPROM memory into the wiper position register (or 1
of 100 decoder). The value of this register can then be set to another wiper position if desired, by using
the 3-terminal control port. On power-up, wiper position will be loaded within a maximum time period of
500 μs once the power-supply is stable. Additionally, the 3-terminal interface port will be active after 50ms.
On power-down, the wiper position register data will be lost. On the next device power-up, the value of
EEPROM memory will be loaded into the wiper position register.
On shipment from the factory, Dallas Semiconductor does not guarantee a specified EEPROM memory
value. This value should be set by the customer as needed.
NONVOLATILE WIPER STORAGE

Wiper position of the DS1804 can be stored using the INC and CS inputs. Storage of the wiper position
takes place, whenever the CS input transitions from low-to-high while the INC is high. Once this
condition has occurred the value of the current wiper position will be written to EEPROM memory.
The DS1804 is specified to accept 50,000 writes to EEPROM before a wear-out condition. After wear-out
the DS1804 will still function and wiper position can be changed during powered conditions using the 3-
terminal control port. However, on power-up the wiper-position will be indeterminate.
ONE TIME PROGRAMMABILITY (OTP)

The DS1804 can be easily used as an OTP device. The user of the DS1804 can trim the desired value of
the wiper position and set this position for storage as described above. Any activity through the 3-
terminal port can then be prevented by connecting the CS input pin to VCC. Also, an OTP application
does not adversely affect the number of times EEPROM is written, since EEPROM will only be loaded
and not written during a power-up or power-down condition.
On power-up the DS1804 will load the current value of EEPROM memory into the wiper position
register.
DS1804
ABSOLUTE MAXIMUM RATINGS*

Voltage on Any Pin Relative to Ground-1.0V to +7.0V
Operating Temperature-40°C to +85°C
Storage Temperature-55°C to +125°C
Soldering Temperature260°C for 10 seconds
* This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operation sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect reliability.
1. Insert A (Burn-in Disclaimer)
The Dallas Semiconductor DS1804 is built to the highest quality standards and manufactured for long
term reliability. All Dallas Semiconductor devices are made using the same quality materials and
manufacturing methods. However, the Flip Chip Package version of the DS1804 is not exposed to
environmental stresses, such as burn-in, that some industrial applications require. For specific reliabilityinformation on this product, please contact the factory in Dallas at (972) 371-4448.
RECOMMENDED DC OPERATING CONDITIONS
(-40°C to +85°C)
DC ELECTRICAL CHARACTERISTICS
(-40°C to +85°C; VCC=2.7V to 5.5V)
DS1804
ANALOG RESISTOR CHARACTERISTICS
(-40°C to +85°C;VCC=2.7V to 5.5V)
CAPACITANCE
(25°C; VCC=2.7V to 5.5V)
AC ELECTRICAL CHARACTERISTICS
(-40°C to +85°C; VCC=2.7V to 5.5V)
DS1804
NOTES:

1. All voltages are referenced to ground.
2. Valid for VCC = 5V only.
3. Resistor input voltages cannot go below ground or exceed VCC by the amounts as shown in the table.
4. Maximum current specifications are based on the clock rate of INC input. This specificationrepresents the current required when changing the wiper position.
5. Standby current levels apply when all inputs are driven to appropriate supply levels. CS, INC, U/D =VCC.
6. Wiper load time is specified as the time required for the DS1804 to load the wiper position with the
contents of nonvolatile memory once VCC has reached a stable operating voltage equal to or greater
than 2.7V.
7. The DS1804 is available in three resistor values. These include the DS1804-010; 10 kΩ, the DS1804-
050 50 kΩ; and the DS1804-100 100 kΩ.
8. Valid at 25°C only.
9. Absolute linearity is used to compare measured wiper voltage versus expected wiper voltage asdetermined by wiper position. The DS1804 is specified to provide an absolute linearity of ±0.60 LSB.
10. Relative linearity is used to determined the change in voltage between successive tap positions. TheDS1804 is specified to provide a relative linearity specification of ±0.25 LSB.
11. -3 dB cutoff frequency characteristics for the DS1804 depend on potentiometer total resistance.
DS1804-010, 1 MHz, DS1804-050; 200 kHz, and DS1804-100; 100 kHz.
12. Capacitance values apply at 25°C.
13. See Figure 2.
14. Power-up time is specified as the time required before the 3-terminal control becomes active after a
stable power supply level has been reached.
15. At VCC = 2.7V, VIL = 0.8V.
16. The INC low toCS inactive is specified to be 50 ns minimum. This is the transition condition which
allows the DS1804 3-terminal port to become inactive without writing the EEPROM memory of the
part.
17. Wiper Storage Time, tWST, is the time require for the DS1804 to write EEPROM memory for storageof a new wiper position. The maximum time required to accomplish this task is specified at 10 ms.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED