IC Phoenix
 
Home ›  DD25 > DS1667-010-DS1667-100,Digital Resistor with OP AMP
DS1667-010-DS1667-100 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
DS1667-010 |DS1667010DALLASN/a10avaiDigital Resistor with OP AMP
DS1667-100 |DS1667100DALLASN/a22avaiDigital Resistor with OP AMP


DS1667-100 ,Digital Resistor with OP AMPBLOCK DIAGRAM Figure 1Information is written to and read from the wiper 0 and wiper 1 registers and ..
DS1669 ,Dallastat Electronic Digital RheostatPIN DESCRIPTION DS1669 R - High Terminal of Potentiometer H R - Wiper Terminal of Potentiometer ..
DS1669-010 , Dallastat Electronic Digital Rheostat
DS1669-050 ,Dallastat Electronic Digital RheostatPIN DESCRIPTION DS1669R - High Terminal of PotentiometerHR - Wiper Terminal of PotentiometerWR - Lo ..
DS1669-10 ,Electronic digital rheostat, ~ 10 k.Applications include volume, tone, contrast,brightness, and dimmer control8-Pin SOIC (208-mil) Ava ..
DS1669-10 ,Electronic digital rheostat, ~ 10 k.Applications include volume, tone, contrast,brightness, and dimmer control8-Pin SOIC (208-mil) Ava ..
DTV110 ,CRT HORIZONTAL DEFLECTION HIGH VOLTAGE DAMPER DIODEFEATURES AND BENEFITSHIGH BREAKDOWN VOLTAGE CAPABILITYISOWATT220ACTO-220ACVERY FAST RECOVERY DIODED ..
DTV110F ,CRT HORIZONTAL DEFLECTION HIGH VOLTAGE DAMPER DIODEFEATURES AND BENEFITSHIGH BREAKDOWN VOLTAGE CAPABILITYISOWATT220ACTO-220ACVERY FAST RECOVERY DIODED ..
DTV1500 ,CRT HORIZONTAL DEFLECTION HIGH VOLTAGE DAMPER DIODEABSOLUTE MAXIMUM RATINGSSymbol Parameter Value UnitV Repetitive peak reverse voltage 1500 VRRMI RMS ..
DTV1500H ,HIGH VOLTAGE DAMPER DIODE (CRT HORIZONTAL DEFLECTION)ABSOLUTE MAXIMUM RATINGSSymbol Parameter Value UnitV Repetitive peak reverse voltage 1500 VRRMI RMS ..
DTV1500HD ,HIGH VOLTAGE DAMPER DIODE (CRT HORIZONTAL DEFLECTION)ABSOLUTE MAXIMUM RATINGSSymbol Parameter Value UnitV Repetitive peak reverse voltage 1500 VRRMI RMS ..
DTV1500HFP ,High voltage diode especially designed for horizontal deflection, 1500V, 6A, 125 nsFEATURES AND BENEFITSAn High breakdown voltage capabilityKn High frequency operationTO-220FPACn Spe ..


DS1667-010-DS1667-100
Digital Resistor with OP AMP
FEATURESTwo digitally controlled 256-position
potentiometersSerial port provides means for setting and
reading both potentiometersResistors can be connected in series to
provide additional resolutionDefault wiper position on power up is 50%Resistive elements are temperature-
compensated to +20% end to endTwo high-gain, wide bandwidth operational
amplifiersLow power CMOS designApplications include analog-to-digital and
digital-to-analog converters, variableoscillators, and variable gain amplifiers20-pin DIP package or optional 20-pin SOIC
surface mount packageOperating temperature range
- Commercial: 0°C to 70°CResistance values:
RESOLUTION-3 dB POINT
DS1667-10:10k 39 ohms1.1 MHzDS1667-50:50k 195 ohms200 kHz
DS1667-100:100k 390 ohms100 kHz
PIN ASSIGNMENT
PIN DESCRIPTION

VCC- +5-Volt Supply
GND- GroundL0, L1- Low End of Resistor
H0, H1- High End of Resistor
W0, W1- Wiper End of Resistor- Substrate Bias and OP
AMP Negative SupplySOUT- Wiper for Stacked
Configuration
RST- Serial Port Reset Input- Serial Port Input/Output
CLK- Serial Port Clock Input
COUT- Cascade Serial Port Output
NINV0, NINVI- Noninverting OP AMP
Input
INV0, INVI- Inverting OP AMP Input
OUT0, OUT1- OP AMP Outputs
DESCRIPTION

The DS1667 is a dual-solid state potentiometer that is adjustable by digitally selected resistive elements.
Each potentiometer is composed of 256 resistive elements. Between each resistive section of each
potentiometer are tap points accessible to the wiper. The position of the wiper on the resistive array is set
by an 8-bit register that controls which tap point is connected to the wiper output. Each 8-bit register can
be read or written by sending or receiving data bits over a 3-wire serial port. In addition, the resistors canbe stacked such that a single potentiometer of 512 sections results. When two separate potentiometers are
DS1667
Digital Resistor with OP AMP

20-Pin DIP (300-mil) and 20-Pin SOICSee Mech. Drawings Section
VCC
OUT0
SOUT
COUT
INVI
NINVI
NINV0
INV0
RST
OUT1
CLK
GND
DS1667
same. The DS1667 also contains two high gain wide bandwidth operational amplifiers. Each amplifier
has both the inverting and non-inverting inputs and the output available for user configuration. The
operational amplifiers can be paired with the resistive elements to perform such functions as analog to
digital conversion, digital to analog conversion, variable gain amplifiers, and variable oscillators.
OPERATION - DIGITAL RESISTOR SECTION

The DS1667 contains two potentiometers, each of which has its wiper set by a value contained in an 8-bit
register (see Figure 1). Each potentiometer consists of 256 resistors of equal value with tap points
between each resistor and at the low end.
In addition, the potentiometer can be stacked by connecting them in series such that the high end ofpotentiometer 0 is connected to the low end of potentiometer 1. When stacking potentiometers, the stack
select bit is used to select which potentiometer wiper will appear at the stack multiplexer output (SOUT).
A zero written to the stack multiplexer will connect wiper 0 to the SOUT pin. This wiper will determine
which of the 256 bottom taps of the stacked potentiometer is selected. When a 1 is written to the stack
multiplexer, wiper 1 is selected and one of the upper 256 taps of the stacked potentiometer is presented atthe SOUT pin.
BLOCK DIAGRAM Figure 1

Information is written to and read from the wiper 0 and wiper 1 registers and the stack select bit via the
17-bit I/O shift register. The I/O shift register is serially loaded by a 3-wire serial port consisting of RST,
DQ, and CLK. It is updated by transferring all 17 bits (Figure 2). Data can be entered into the 17-bit shift
register only when the RST input is at a high level. While at a high level, the RST function allows serial
entry of data via the D/Q pin. The potentiometers always maintain their previous value until RST is
DS1667
Valid data is entered into the I/O shift register while RST is high on the low-to-high transition of the
CLK input. Data input on the DQ pin can be changed while the clock input is high or low, but only data
meeting the setup requirements will enter the shift register. Data is always entered starting with the value
of the stack select bit. The next 8 bits to be entered are those specifying the wiper 1 setting. The MSB ofthese 8 bits is sent first. The next 8 bits to be entered are those specifying the wiper 0 setting, sent MSB
first. The 17th bit to be entered, therefore, will be the least significant bit of the wiper 0 setting. If fewer
than 17 bits are entered, the value of the potentiometer settings will result from the number of bits that
were entered plus the remaining bits of the old value shifted over by the number of bits sent. If more than
17 bits are sent, only the last 17 bits are left in the shift register. Therefore, sending other than 17 bits canproduce indeterminate potentiometer settings.
As bits are entered into the shift register, the previous value is shifted out bit by bit on the cascade serial
port pin (COUT). By connecting the COUT pin to the DQ pin of a second DS1667, multiple devices can
be daisy chained together as shown in Figure 3.
When connecting multiple devices, the total number of bits sent is always 17 times the number of
DS1667s in the daisy chain. In applications where it is desirable to read the settings of potentiometers, the
COUT pin of the last device connected in a daisy chain must be connected back to the DQ input of the
first device through a resistor with a value of 1k to 10k. This resistor provides isolation between COUTand DQ when writing to the device (see Figure 3).
When reading data, the DQ line is left floating by the reading device. When RST is held low, bit 17 is
always present on the COUT pin, which is fed back to the input DQ pin through the resistor (see Figure
4). This data bit can now be read by the reading device. The RST pin is then transitioned high to initiate a
data transfer. When the CLK input transitions low to high, bit 17 is loaded into the first position of the
I/O shift register and bit 16 becomes present on COUT and DQ. After 17 bits (or 17 times the number ofdevices for a daisy chain), the data has shifted completely around and back to its original position. When
RST is transitioned back low to end data transfer, the value (the same as before the read occurred) is
loaded into the wiper 0 and wiper 1 registers and the stack select bit.
When power is applied to the DS1667, the device always has the wiper settings at half position and the
stack select bit is at 0.
DS1667
WRITING DATA Figure 2
CASCADING MULTIPLE DEVICES Figure 3
READING DATA Figure 4
DS1667
DS1667 LINEARITY MEASUREMENTS

An important specification for the DS1667 is linearity, that is, for a given digital input, how close the
analog output is to that which is expected.
The test circuit used to measure the linearity of the DS1667 is shown in Figure 5. Note that to get an
accurate output voltage it is necessary to assure that the output current is 0, in order to negate the effectsof wiper impedance RW, which is typically 400 ohms. For any given setting N for the pot, the expected
voltage output at SOUT is:
VO = -5 + [10 X (N/256)] (in volts)
Absolute linearity is a comparison of the actual measured output voltage versus the expected value given
by the equation above and is given in terms of an LSB, which is the change in expected output when the
digital input is incremented by 1. In this case the LSB is 10/256 or 0.03906 volts. The equation for the
absolute linearity of the DS1667 is:
LSB
The specification for absolute linearity of the DS1667 is + 1 LSB typical.
Relative linearity is a comparison of the difference of actual output voltages of two successive taps andthe difference of the expected output voltages of two successive taps. The expected difference of output
voltages is 1 LSB or 0.03906V for the measurement system of Figure 5. Relative linearity is expressed in
terms of an LSB and is given by the equation:
LSB
The specification for relative linearity of the DS1667 is ± 0.5 LSB typical.
Figure 6 is a plot of absolute linearity (AL) and relative linearity (RL) versus wiper setting for a typical
DS1667 at 25°C.
DESCRIPTION AND OPERATION - OP AMP SECTION

The DS1667 contains two operational amplifiers which are ideal for operation from a single 5V supply
and ground or from +5V supplies (see Figure 1). An internal resistor divider defines the internal reference
of the op amp to be halfway between the power supplies, i.e.:
For optimal performance, choose analog ground to be this value. The operational amplifiers feature rail to
rail output swing in addition to an input common mode range that includes the positive rail. Performance
features include broad band noise immunity as well as voltage gain into realistic loads specified at both
600 ohms and 2k ohms. High voltage gain is produced with low input offset voltage and low offset
voltage drift. Current consumption is less than 1.9 mA per amplifier and the device is virtually immune tolatchup.
DS1667
LINEARITY MEASUREMENT CONFIGURATION Figure 5
DS1667 ABSOLUTE AND RELATIVE LINEARITY Figure 6

Absolute and Relative Linearity
(Normalized to 1 LSB)
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED