IC Phoenix
 
Home ›  DD24 > DS1553-100-DS1553-70-DS1553P-100-DS1553P-70-DS1553W-120-DS1553WP-120-DS1553WP-150,4MEG NV Y2KC Timekeeping RAM
DS1553-100-DS1553-70-DS1553P-100-DS1553P-70-DS1553W-120 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
DS1553-100 |DS1553100DALLAS特价N/a150avai64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
DS1553-70 |DS155370DALLASN/a65avai64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
DS1553P-100 |DS1553P100DALLASN/a398avai4MEG NV Y2KC Timekeeping RAM
DS1553P-70 |DS1553P70DALLASN/a58avai4MEG NV Y2KC Timekeeping RAM
DS1553P-70 |DS1553P70MAXN/a136avai4MEG NV Y2KC Timekeeping RAM
DS1553P-70 |DS1553P70DALLSN/a194avai4MEG NV Y2KC Timekeeping RAM
DS1553W-120 |DS1553W120DALLASN/a200avai64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
DS1553WP-120 |DS1553WP120DALLAS ?N/a5avai4MEG NV Y2KC Timekeeping RAM
DS1553WP-120 |DS1553WP120MAXN/a233avai4MEG NV Y2KC Timekeeping RAM
DS1553WP-120 |DS1553WP120DALLSN/a133avai4MEG NV Y2KC Timekeeping RAM
DS1553WP-120 |DS1553WP120DALLASN/a2124avai4MEG NV Y2KC Timekeeping RAM
DS1553WP-150 |DS1553WP150MAXN/a11avai4MEG NV Y2KC Timekeeping RAM
DS1553WP-150 |DS1553WP150DALLASN/a113avai4MEG NV Y2KC Timekeeping RAM


DS1553WP-120 ,4MEG NV Y2KC Timekeeping RAMPIN DESCRIPTION A0–A12 - Address Input DQ0–DQ7 - Data Input/Outputs IRQ /FT - Interrupt, Frequen ..
DS1553WP-120 ,4MEG NV Y2KC Timekeeping RAMFEATURES The DS1553 is a full-function, year-2000-compliant  Integrated NV SRAM, RTC, Crystal, Po ..
DS1553WP-120 ,4MEG NV Y2KC Timekeeping RAM DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
DS1553WP-120 ,4MEG NV Y2KC Timekeeping RAMFEATURES The DS1553 is a full-function, year-2000-compliant  Integrated NV SRAM, RTC, Crystal, Po ..
DS1553WP-150 ,4MEG NV Y2KC Timekeeping RAMPIN DESCRIPTION A0–A12 - Address Input DQ0–DQ7 - Data Input/Outputs IRQ /FT - Interrupt, Frequen ..
DS1553WP-150 ,4MEG NV Y2KC Timekeeping RAM DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
DTC144WS , DTA/DTC SERIES
DTC314TS , Digital transistors (built-in resistor)
DTC314TU , Digital transistors (built-in resistor)
DTC323TS , Digital transistors (built-in resistor)
DTC323-TS , Digital transistors (built-in resistor)
DTC343TS , Digital transistors (built-in resistor)


DS1553-100-DS1553-70-DS1553P-100-DS1553P-70-DS1553W-120-DS1553WP-120-DS1553WP-150
64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
GENERAL DESCRIPTION
The DS1553 is a full-function, year-2000-compliant
(Y2KC) real-time clock/calendar (RTC) with an RTC alarm, watchdog timer, power-on reset, battery
monitor, and 8k x 8 nonvolatile static RAM. User
access to all registers within the DS1553 is
accomplished with a bytewide interface as shown in Figure 1. The RTC registers contain century, year,
month, date, day, hours, minutes, and seconds data in 24-hour BCD format. Corrections for day of month and
leap year are made automatically. ORDERING INFORMATION
*PowerCap required, must be ordered separately.
FEATURES

��Integrated NV SRAM, RTC, Crystal, Power-Fail
Control Circuit, and Lithium Energy Source
��Clock Registers are Accessed Identically to the
Static RAM; These Registers are Resident in the 16
Top RAM Locations
��Totally Nonvolatile with Over 10 Years of
Operation in the Absence of Power
��Precision Power-On Reset
��Programmable Watchdog Timer and RTC Alarm
��BCD-Coded Year, Month, Date, Day, Hours,
Minutes, and Seconds with Automatic Leap Year Compensation Valid Up to the Year 2100 Battery Voltage Level Indicator Flag Power-Fail Write Protection Allows for �10% VCC Power-Supply Tolerance
��Lithium Energy Source is Electrically
Disconnected to Retain Freshness Until Power is
Applied for the First Time
PIN CONFIGURATIONS
DS1553
64kB, Nonvolatile, Year-2000-Compliant
Timekeeping RAM

PowerCap is a registered trademark of Dallas Semiconductor.
DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
PIN DESCRIPTION

A0–A12 - Address Input
DQ0–DQ7 - Data Input/Outputs
IRQ/FT - Interrupt, Frequency Test Output
(Open Drain)
RST - Power-On Reset Output (Open Drain) - Chip Enable - Output Enable - Write Enable
VCC - Power-Supply Input
GND - Ground N.C. - No Connection DETAILED DESCRIPTION
The RTC registers in the DS1553 are double-buffered into an internal and external set. The user has direct
access to the external set. Clock/calendar updates to the external set of registers can be disabled and
enabled to allow the user to access static data. Assuming the internal oscillator is turned on, the internal set of registers is continuously updated. This occurs regardless of external registers settings to guarantee
that accurate RTC information is always maintained.
The DS1553 has interrupt (IRQ/FT) and reset (RST) outputs that can be used to control CPU activity.
The IRQ/FT interrupt output can be used to generate an external interrupt when the RTC register values
match user-programmed alarm values. The interrupt is always available while the device is powered from
the system supply, and it can be programmed to occur when in the battery-backed state to serve as a
system wakeup. Either the IRQ/FT or RST outputs can also be used as a CPU watchdog timer. CPU
activity is monitored and an interrupt or reset output is activated if the correct activity is not detected within programmed limits. The DS1553 power-on reset can be used to detect a system power-down or
failure and can hold the CPU in a safe reset state until normal power returns and stabilizes. The RST
output is used for this function.
The DS1553 also contains its own power-fail circuitry, which automatically deselects the device when the
VCC supply enters an out-of-tolerance condition. This feature provides a high degree of data security
during unpredictable system operation brought on by low VCC levels.
PACKAGES

The DS1553 is available in a 28-pin DIP and a 34-pin PowerCap module. The 28-pin DIP module
integrates the crystal, lithium energy source, and silicon in one package. The 34-pin PowerCap module
board is designed with contacts for connection to a separate PowerCap (DS9034PCX) that contains the
crystal and battery. This design allows the PowerCap to be mounted on top of the DS1553P after completion of the surface-mount process. Mounting the PowerCap after the surface-mount process
prevents damage to the crystal and battery due to the high temperatures required for solder reflow. The
PowerCap is keyed to prevent reverse insertion. The PowerCap module board and PowerCap are ordered
separately and shipped in separate containers. The part number for the PowerCap is DS9034PCX.
DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
Figure 1. Block Diagram

Table 1. Operating Modes

DATA READ MODE

The DS1553 is in read mode whenever CE (chip enable) is low and WE (write enable) is high. The
device architecture allows ripple-through access to any valid address location. Valid data is available at
the data input/output (DQ) pins within tAA after the last address input is stable, provided that CE and OE
access times are satisfied. If CE or OE access times are not met, valid data is available at the latter of
chip-enable access (tCEA) or at output-enable access time (tOEA). The state of the DQ pins is controlled by and OE. If the outputs are activated before tAA, the data lines are driven to an intermediate state until
tAA. If the address inputs are changed while CE and OE remain valid, output data remains valid for
output data hold time (tOH) but will then go indeterminate until the next address access.
DATA WRITE MODE

The DS1553 is in write mode whenever WE and CE are in their active state. The start of a write is
referenced to the latter occurring transition of WE or CE. The addresses must be held valid throughout
the cycle. CE and WE must return inactive for a minimum of tWR prior to the initiation of a subsequent
read or write cycle. Data in must be valid tDS prior to the end of the write and remain valid for tDH
afterward. In a typical application, the OE signal is high during a write cycle. However, OE can be active
DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
transitioning low, the data bus can become active with read data defined by the address inputs. A low
transition on WE will then disable the outputs tWEZ after WE goes active.
DATA RETENTION MODE

The 5V device is fully accessible, and data can be written and read only when VCC is greater than VPF.
However, when VCC is below the power-fail point (VPF)—the point at which write protection occurs—the
internal clock registers and SRAM are blocked from any access. When VCC falls below the battery switch
point VSO (battery supply level), device power is switched from the VCC pin to the internal backup lithium
battery. RTC operation and SRAM data are maintained from the battery until VCC is returned to nominal levels.
The 3.3V device is fully accessible and data can be written and read only when VCC is greater than VPF.
When VCC falls below VPF, access to the device is inhibited. If VPF is less than VSO, the device power is
switched from VCC to the internal backup lithium battery when VCC drops below VPF. If VPF is greater
than VSO, the device power is switched from VCC to the internal backup lithium battery when VCC drops below VSO. RTC operation and SRAM data are maintained from the battery until VCC is returned to
nominal levels.
All control, data, and address signals must be powered down when VCC is powered down.
BATTERY LONGEVITY

The DS1553 has a lithium power source that is designed to provide energy for the clock activity and
clock and RAM data retention when the VCC supply is not present. The capability of this internal power
supply is sufficient to power the DS1553 continuously for the life of the equipment in which it is
installed. For specification purposes, the life expectancy is 10 years at +25�C with the internal clock
oscillator running in the absence of VCC. Each DS1553 is shipped from Dallas Semiconductor with its lithium energy source disconnected, guaranteeing full energy capacity. When VCC is first applied at a
level greater than VPF, the lithium energy source is enabled for battery backup operation.
INTERNAL BATTERY MONITOR

The DS1553 constantly monitors the battery voltage of the internal battery. The Battery Low Flag (BLF)
bit of the Flags register (B4 of 1FF0h) is not writeable and should always be 0 when read. If a 1 is ever present, an exhausted lithium energy source is indicated, and both the contents of the RTC and RAM are
questionable.
POWER-ON RESET

A temperature-compensated comparator circuit monitors the VCC level. When VCC falls to the power-fail
trip point, the RST signal (open drain) is pulled low. When VCC returns to nominal levels, the RSTsignal continues to be pulled low for 40ms to 200ms. The power-on reset function is independent of the RTC
oscillator and is therefore operational whether or not the oscillator is enabled.
DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
CLOCK OPERATIONS

Table 2 and the following paragraphs describe the operation of RTC, alarm, and watchdog functions.
Table 2. Register Map

X = Unused, Read/Writable Under Write and Read Bit Control AE = Alarm Flag Enable
FT = Frequency Test Bit Y = Unused, Read/Writable Without Write and Read Bit Control
OSC = Oscillator Start/Stop Bit ABE = Alarm in Battery-Backup Mode Enable
W = Write Bit AM1–AM4 = Alarm Mask Bits
R = Read Bit WF = Watchdog Flag
WDS = Watchdog Steering Bit AF = Alarm Flag
BMB0–BMB4 = Watchdog Multiplier Bits 0 = 0 Read Only
RB0–RB1 = Watchdog Resolution Bits BLF = Battery Low Flag CLOCK OSCILLATOR CONTROL
The clock oscillator may be stopped at any time. To increase the shelf life of the backup lithium battery
source, the oscillator can be turned off to minimize current drain from the battery. The OSC bit is the
MSB of the Seconds register (B7 of 1FF9h). Setting it to 1 stops the oscillator; setting it to 0 starts the
oscillator. The DS1553 is shipped from Dallas Semiconductor with the clock oscillator turned off, with
the OSC bit set to 1.
READING THE CLOCK

When reading the RTC data, it is recommended to halt updates to the external set of double-buffered RTC
registers. This puts the external registers into a static state, allowing data to be read without register
values changing during the read process. Normal updates to the internal registers continue while in this
state. External updates are halted when a 1 is written into the read bit, B6 of the Control register (1FF8h).
DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
was issued. Normal updates to the external set of registers resume within 1 second after the read bit is set
to 0 for a minimum of 500�s. The read bit must be 0 for a minimum of 500�s to ensure the external registers are updated.
SETTING THE CLOCK

The 8th bit, B7 of the Control register, is the write bit. Setting the write bit to 1, like the read bit, halts
updates to the DS1553 (1FF8h–1FFFh) registers. After setting the write bit to 1, RTC registers can be loaded with the desired RTC count (day, date, and time) in 24-hour BCD format. Setting the write bit to 0
then transfers the values written to the internal RTC registers and allows normal operation to resume.
CLOCK ACCURACY (DIP MODULE)

The DS1553 is guaranteed to keep time accuracy to within �1 minute per month at +25�C. The RTC is calibrated at the factory by Dallas Semiconductor using nonvolatile tuning elements and does not require
additional calibration. For this reason, methods of field clock calibration are not available and not
necessary. The electrical environment also affects clock accuracy and caution should be taken to place the
RTC in the lowest level EMI section of the PC board layout. For additional information, refer to
Application Note 58: Crystal Considerations with Dallas Real-Time Clocks on our website at /appnoteindex.com.
CLOCK ACCURACY (PowerCap MODULE)

The DS1553 and DS9034PCX are each individually tested for accuracy. Once mounted together, the
module typically keeps time accuracy to within �1.53 minutes per month (35ppm) at +25°C. The electrical environment affects clock accuracy and caution should be taken to place the RTC in the lowest
level EMI section of the PC board layout. For additional information, refer to Application Note 58:
Crystal Considerations with Dallas Real-Time Clocks on our website at www.maxim-
ic.com/appnoteindex.com.
FREQUENCY TEST MODE

The DS1553 frequency test mode uses the open-drain IRQ/FT output. With the oscillator running, the
IRQ/FT output toggles at 512Hz when the FT bit is 1, the Alarm Flag Enable bit (AE) is 0, and the
Watchdog Steering bit (WDS) is 1 or the Watchdog register is reset (Register 1FF7h = 00h). The IRQ/FT
output and the frequency test mode can be used as a measure of the actual frequency of the 32.768kHz
RTC oscillator. The IRQ/FT pin is an open-drain output that requires a pullup resistor for proper
operation. The FT bit is cleared to 0 on power-up.
USING THE CLOCK ALARM

The alarm settings and control for the DS1553 reside within registers 1FF2h–1FF5h. Register 1FF6h
contains two alarm-enable bits: Alarm Enable (AE) and Alarm in Backup Enable (ABE). The AE and
ABE bits must be set as described below for the IRQ/FT output to be activated for a matched alarm
condition.
The alarm can be programmed to activate on a specific day of the month or repeat every day, hour,
minute, or second. It can also be programmed to go off while the DS1553 is in the battery-backed state of
operation to serve as a system wakeup. Alarm mask bits AM1–AM4 control the alarm mode. Table 3
shows the possible settings. Configurations not listed in the table default to the once-per-second mode to
DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
Table 3. Alarm Mask Bits

When the RTC register values match Alarm register settings, the Alarm Flag bit (AF) is set to 1. If the
Alarm Flag Enable (AE) is also set to 1, the alarm condition activates the IRQ/FT pin. The IRQ/FT signal
is cleared by a read or write to the Flags register (Address 1FF0h) as shown in Figures 2 and 3. When CE
is active, the IRQ/FT signal may be cleared by having the address stable for as short as 15ns and either or WE active, but it is not guaranteed to be cleared unless tRC is fulfilled. The alarm flag is also
cleared by a read or write to the Flags register, but the flag does not change states until the end of the
read/write cycle and the IRQ/FT signal has been cleared.
Figure 2. Clearing IRQ Waveforms

Figure 3. Clearing IRQ Waveforms

The IRQ/FT pin can also be activated in the battery-backed mode. The IRQ/FT goes low if an alarm
occurs and both ABE and AE are set. The ABE and AE bits are cleared during the power-up transition,
however, an alarm generated during power-up sets AF. Therefore, the AF bit can be read after system
power-up to determine if an alarm was generated during the power-up sequence. Figure 4 illustrates alarm
DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
Figure 4. Backup Mode Alarm Waveforms
USING THE WATCHDOG TIMER
The watchdog timer can be used to detect an out-of-control processor. The user programs the watchdog
timer by setting the desired amount of timeout into the 8-bit Watchdog register (Address 1FF7h). The five
Watchdog register bits BMB4–BMB0 store a binary multiplier and the two lower-order bits
RB1–RB0 select the resolution, where 00 = 1/16 second, 01 = 1/4 second, 10 = 1 second, and 11 = 4 seconds. The watchdog timeout value is then determined by the multiplication of the 5-bit
multiplier value with the 2-bit resolution value. (For example: writing 00001110 in the Watchdog register
= 3 x 1 second or 3 seconds.) If the processor does not reset the timer within the specified period, the
Watchdog Flag (WF) is set and a processor interrupt is generated and stays active until either the
Watchdog Flag (WF) is read or the Watchdog register (1FF7) is read or written.
The most significant bit of the Watchdog register is the Watchdog Steering Bit (WDS). When set to 0, the
watchdog activates the IRQ/FT output when the watchdog times out.
When WDS is set to 1, the watchdog outputs a negative pulse on the RSToutput for 40ms to 200ms. The
Watchdog register (1FF7) and the FT bit are reset to 0 at the end of a watchdog timeout when the WDS
bit is set to 1.
The watchdog timer resets when the processor performs a read or write of the Watchdog register. The timeout period then starts over. Writing a value of 00h to the Watchdog register disables the watchdog
timer. The watchdog function is automatically disabled upon power-up and the Watchdog register is
cleared. If the watchdog function is set to output to the IRQ/FT output and the frequency test function is
activated, the watchdog function prevails and the frequency test function is denied.
POWER-ON DEFAULT STATES

Upon application of power to the device, the following register bits are set to 0:
WDS = 0, BMB0–BMB4 = 0, RB0–RB1 = 0, AE = 0, and ABE = 0.
DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
ABSOLUTE MAXIMUM RATINGS

Voltage Range on Any Pin Relative to Ground -0.3V to +6.0V
Storage Temperature Range -40�C to +85�C Soldering Temperature 260°C for 10 seconds (DIP Package) (Note 8)
See IPC/JEDEC Standard J-STD-020A for
Surface Mount Devices
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation
sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. OPERATING RANGE
RECOMMENDED DC OPERATING CONDITIONS

(Over the operating range)
DC ELECTRICAL CHARACTERISTICS

(VCC = 5.0V ±10%, over the operating range.)
DS1553 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM
DC ELECTRICAL CHARACTERISTICS

(VCC = 3.3V ±10%, over the operating range.)
Figure 5. Read Cycle Timing Diagram
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED