IC Phoenix
 
Home ›  BB32 > BTS462T,Smart Power High-Side-Switch
BTS462T Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
BTS462TINFINEONN/a8200avaiSmart Power High-Side-Switch


BTS462T ,Smart Power High-Side-SwitchFeatures Product Summary• Overload protection Overvoltage protection V 41 Vbb(AZ)• Current limitati ..
BTS4880R ,Smart Power High-Side-Switch Eight Channels: 8 x 200 mGeneral DescriptionN channel vertical power FET with charge pump, ground referenced CMOS or V /2 bb ..
BTS4880R . ,Smart Power High-Side-Switch Eight Channels: 8 x 200 mFeatures Product Summary• Output current 0,625 A per channel Overvoltage protection V 47 Vbb(AZ)• S ..
BTS50080-1TMA , Smart High-Side Power Switch
BTS5012SDA , Smart High-Side Power Switch PROFET™ One Channel
BTS5016SDA , Smart High-Side Power Switch PROFET™ One Channel
BZX84C5V1LT1 ,SEMICONDUCTOR(TECHNICAL DATA)ELECTRICAL CHARACTERISTICS − BZX84BxxxL (Tight Tolerance Series)(Pinout: 1-Anode, 2-No Connection, ..
BZX84C5V1LT1G , Zener Voltage Regulators
BZX84C5V1T-7-F , 150mW SURFACE MOUNT ZENER DIODE
BZX84C5V1TS-7-F , TRIPLE SURFACE MOUNT ZENER DIODE ARRAY
BZX84C5V1-V-GS08 , Small Signal Zener Diodes
BZX84C5V1W-7-F , 200mW SURFACE MOUNT ZENER DIODE


BTS462T
Smart Power High-Side-Switch
BTS 462 T
Smart Power High-Side-Switch
Features

• Overload protection
• Current limitation
• Short circuit protection
• Thermal shutdown with restart
• Overvoltage protection
(including load dump)
• Fast demagnetization of inductive loads
• Reverse battery protection
with external resistor
• CMOS compatible input
• Loss of GND and loss of Vbb protection
• ESD - Protection
• Very low standby current
Product Summary

P-TO252-5-11
Application

• All types of resistive, inductive and capacitive loads
• µC compatible power switch for 12 V and 24 V DC applications
• Replaces electromechanical relays and discrete circuits
General Description

N channel vertical power FET with charge pump, ground referenced CMOS compatible input,
monolithically integrated in Smart SIPMOS technology.
Providing embedded protective functions.
BTS 462 T
Block Diagram

Signal GND
miniPROFET
Load GND
VLogic
Pin configuration
BTS 462 T
Maximum Ratings at Tj = 25°C, unless otherwise specified
Thermal Characteristics

1Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6 cm2 (one layer, 70µm thick) copper area for drain
connection. PCB is vertical without blown air. (see page 16)
2not subject to production test, specified by design
3VLoaddump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 .
Supply voltages higher than Vbb(AZ) require an external current limit for the GND pin, e.g. with a
150Ω resistor in GND connection. A resistor for the protection of the input is integrated.
BTS 462 T
Electrical Characteristics
Load Switching Capabilities and Characteristics
Operating Parameters
BTS 462 T
Electrical Characteristics
Protection Functions
1)
Reverse Battery

1Integrated protection functions are designed to prevent IC destruction under fault conditions
described in the data sheet. Fault conditions are considered as "outside" normal operating range.
Protection functions are not designed for continuous repetitive operation.
2 see also VON(CL) in circuit diagram on page 7
3Requires a 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source diode has
to be limited by the connected load. Power dissipation is higher compared to normal operating conditions due to the
voltage drop across the drain-source diode. The temperature protection is not active during reverse current operation!
BTS 462 T
Input
BTS 462 T
TermsInductive and overvoltage output clamp

GND
PROFET
OUT
GNDININbbbbLOUTIGNDONGND
VON clamped to 47V typ.
Overvoltage protection of logic partInput circuit (ESD protection)
bb
GND
GNDR
Signal GND
Logic
Z2RZ1
GNDRIIIESD-
The use of ESD zener diodes as voltage clamp
at DC conditions is not recommendedZ1=6.1V typ., VZ2=Vbb(AZ)=47V typ.,I=3.5 kΩ typ., RGND=150Ω
Reverse battery protection

GND
Logic
R
Power GND
GNDR
Signal GND
Power
InverseR
DiodeGND=150Ω, RI=3.5kΩ typ.,
Temperature protection is not active during
inverse current
BTS 462 Tbb disconnect with charged inductive
load
PROFET
OUT
GNDbb
high
GND disconnect
PROFET
OUT
GNDbbVINVGND
Inductive Load switch-off energy
dissipation

GND disconnect with GND pull up
PROFET
OUT
GND
Energy stored in load inductance: EL = ½ * L * IL2
While demagnetizing load inductance,
the enérgy dissipated in PROFET isAS = Ebb + EL - ER = VON(CL) * iL(t) dt,
with an approximate solution for RL > 0Ω:ILVVIROUTCL
OUTCL=++**(|)*ln(*)()|21
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED