IC Phoenix
 
Home ›  BB32 > BTS436L2 S,Smart High Side Switches
BTS436L2 S Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
BTS436L2 S |BTS436L2SINFINEONN/a15000avaiSmart High Side Switches


BTS436L2 S ,Smart High Side SwitchesBlock Diagram Protection Functions Vbb• Short circuit protection • Overload protection • Current l ..
BTS436L2G , Smart High-Side Power Switch One Channel: 38mΩ Status Feedback
BTS441R ,Smart High Side Switches BTS 441 R Smart Highside Power Switch One Channel: 20mΩ Status Feedback Product Summary ..
BTS441R G ,Smart Highside Power Switch One Channel: 20m Status Feedback BTS 441 R Smart Highside Power Switch One Channel: 20mΩ Status Feedback Product Summary ..
BTS441T ,Smart Highside Power Switch One Channel: 20m BTS 441 T Smart Highside Power Switch One Channel: 20mΩ Product Summary ..
BTS442E2 ,Smart Highside Power SwitchFeatures • Overload protection Overvoltage protection V 63 Vbb(AZ)• Current limitation V 4.5 ... 4 ..
BZX84-C56V ,Small Signal Zener DiodesElectrical CharacteristicsPartnumber Marking Zener Dynamic Resistance Test Temp. Test Reverse Leaka ..
BZX84C5V1 ,350mW ZENER DIODE 3.3 VOLTS THRU 33 VOLTS 5% TOLERANCEElectrical CharacteristicsT = 25

BTS436L2 S
Smart High Side Switches
Smart High-Side Power Switch
One Channel: 38mΩ
Status Feedback
Product Summary Package

General Description
N channel vertical power MOSFET with charge pump, ground referenced CMOS compatible input and
diagnostic feedback, monolithically integrated in Smart SIPMOS technology. Providing embedded protective functions
Applications
µC compatible high-side power switch with diagnostic feedback for 5V, 12V and 24V grounded loads All types of resistive, inductive and capacitve loads Most suitable for loads with high inrush currents, so as lamps Replaces electromechanical relays, fuses and discrete circuits
Basic Functions
Very low standby current CMOS compatible input Fast demagnetization of inductive loads Stable behaviour at undervoltage Wide operating voltage range Logic ground independent from load ground
Protection Functions
Short circuit protection Overload protection
• Current limitation
• Thermal shutdown Overvoltage protection (including load dump) with external resistor Reverse battery protection with external resistor Loss of ground and loss of Vbb protection Electrostatic discharge protection (ESD)
Diagnostic Function
Diagnostic feedback with open drain output Open load detection in ON-state Feedback of thermal shutdown in ON-state
TO 220-5-11 TO-263-5-2 TO-220-5-12

Standard SMD Straight
Block Diagram
Functional diagram
Pin Definitions and Functions

Pin configuration
Maximum Ratings at Tj = 25 °C unless otherwise specified
Thermal Characteristics

1) Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins (a 150Ω
resistor for the GND connection is recommended). 2) RI = internal resistance of the load dump test pulse generator 3) VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 4) EAS is the maximum inductive switch-off energy
Electrical Characteristics
Load Switching Capabilities and Characteristics

Operating Parameters

6) not subject to production test, specified by design 7) Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins (a 150Ω
resistor for the GND connection is recommended. See also VON(CL) in table of protection functions and
circuit diagram page 7.
Protection Functions10)
Diagnostic Characteristics

Input and Status Feedback14)

10) Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are not designed for continuous repetitive operation. 11) Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70µm thick) copper area for Vbb
connection. PCB is vertical without blown air.
12) Requires 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source
diode has to be limited by the connected load. Note that the power dissipation is higher compared to normal operating conditions due to the voltage drop across the intrinsic drain-source diode. The temperature
protection is not active during reverse current operation! Input and Status currents have to be limited (see max. ratings page 3 and circuit page 7).
Truth Table L = "Low" Level X = don't care Z = high impedance, potential depends on external circuit
H = "High" Level Status signal after the time delay shown in the diagrams (see fig 5. page 11)
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED