IC Phoenix
 
Home ›  AA18 > AD807-155BR-AD807A-155BR-AD807A-155BRRL7,Fiber Optic Receiver with Quantizer and Clock Recovery and Data Retiming
AD807-155BR-AD807A-155BR-AD807A-155BRRL7 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
AD807-155BR |AD807155BRADIN/a35avaiFiber Optic Receiver with Quantizer and Clock Recovery and Data Retiming
AD807A-155BR |AD807A155BRN/a12avaiFiber Optic Receiver with Quantizer and Clock Recovery and Data Retiming
AD807A-155BRRL7 |AD807A155BRRL7ADIN/a10875avaiFiber Optic Receiver with Quantizer and Clock Recovery and Data Retiming
AD807A-155BRRL7 |AD807A155BRRL7ADN/a38avaiFiber Optic Receiver with Quantizer and Clock Recovery and Data Retiming


AD807A-155BRRL7 ,Fiber Optic Receiver with Quantizer and Clock Recovery and Data RetimingFEATURES frequency acquisition without false lock. This eliminates a reli-Meets CCITT G.958 Require ..
AD808-622BR ,Fiber Optic Receiver with Quantizer and Clock Recovery and Data RetimingFEATURES frequency acquisition without false lock. This eliminates a reli-Meets CCITT G.958 Require ..
AD808-622BRRL7 ,Fiber Optic Receiver with Quantizer and Clock Recovery and Data RetimingSpecifications subject to change without notice.–2– REV. 0AD8081PIN FUNCTION DESCRIPTIONSABSOLUTE M ..
AD808-622BRRL7 ,Fiber Optic Receiver with Quantizer and Clock Recovery and Data RetimingCHARACTERISTICSUpper –3 dB Bandwidth 600 800 MHzInput Resistance 10 kΩInput Capacitance 2pFPulsewid ..
AD8091AR ,Low Cost , High-Speed Rail-to-Rail AmplifiersSPECIFICATIONS unless otherwise noted.) AD8091A/AD8092AParameter Conditions Min Typ Max U ..
AD8091AR-REEL ,Low-Cost, High-Speed Rail-to-Rail AmplifiersAPPLICATIONSAD8091Coaxial Cable DriverV 1 5 +VOUT SActive Filters–V 2SVideo Switchers+IN 3 4 –INPro ..
ADM8692AN ,Microprocessor Supervisory CircuitsFEATURES FUNCTIONAL BLOCK DIAGRAMSUpgrade for ADM690/ADM695, MAX690–MAX695Specified Over Temperatur ..
ADM8692ARN ,Microprocessor Supervisory CircuitsMicroprocessoraSupervisory CircuitsADM8690–ADM8695
ADM8694AN ,Microprocessor Supervisory CircuitsAPPLICATIONS1VOLTAGE DETECTOR = 4.65V (ADM8690, ADM8694)Microprocessor Systems ..
ADM8694ARN ,Microprocessor Supervisory CircuitsGENERAL DESCRIPTIONVOUTThe ADM8690–ADM8695 family of supervisory circuits offersADM8691ADM8693compl ..
ADM8696ARW ,Microprocessor Supervisory CircuitsGENERAL DESCRIPTIONCEINThe ADM8696/ADM8697 supervisory circuits offer complete CEOUTsingle chip sol ..
ADM8697ARW ,Microprocessor Supervisory CircuitsSPECIFICATIONSunless otherwise noted.)Parameter Min Typ Max Units Test Conditions/CommentsV Operati ..


AD807-155BR-AD807A-155BR-AD807A-155BRRL7
Fiber Optic Receiver with Quantizer and Clock Recovery and Data Retiming
REV.AFiber Optic Receiver with Quantizer and
Clock Recovery and Data Retiming
FEATURES
Meets CCITT G.958 Requirements
for STM-1 Regenerator—Type A
Meets Bellcore TR-NWT-000253 Requirements for OC-3
Output Jitter: 2.0 Degrees RMS
155 Mbps Clock Recovery and Data Retiming
Accepts NRZ Data, No Preamble Required
Phase-Locked Loop Type Clock Recovery—
No Crystal Required
Quantizer Sensitivity: 2 mV
Level Detect Range: 2.0 mV to 30 mV
Single Supply Operation: +5 V or –5.2 V
Low Power: 170 mW
10 KH ECL/PECL Compatible Output
Package:16-Pin Narrow 150 mil SOIC

frequency acquisition without false lock. This eliminates a reli-
ance on external components such as a crystal or a SAW filter,
to aid frequency acquisition.
The AD807 acquires frequency and phase lock on input data
using two control loops that work without requiring external
control. The frequency acquisition control loop initially acquires
the frequency of the input data, acquiring frequency lock on
random or scrambled data without the need for a preamble. At
frequency lock, the frequency error is zero and the frequency
detector has no further effect. The phase acquisition control
loop then works to ensure that the output phase tracks the input
phase. A patented phase detector has virtually eliminated pat-
tern jitter throughout the AD807.
The device VCO uses a ring oscillator architecture and patented
low noise design techniques. Jitter is 2.0 degrees rms. This low
jitter results from using a fully differential signal architecture,
Power Supply Rejection Ratio circuitry and a dielectrically
isolated process that provides immunity from extraneous signals
on the IC. The device can withstand hundreds of millivolts of
power supply noise without an effect on jitter performance.
The user sets the jitter peaking and acquisition time of the PLL
by choosing a damping factor capacitor whose value determines
loop damping. CCITT G.958 Type A jitter transfer require-
ments can easily be met with a damping factor of 5 or greater.
Device design guarantees that the clock output frequency will
drift by less than 20% in the absence of input data transitions.
Shorting the damping factor capacitor, CD, brings the clock out-
put frequency to the VCO center frequency.
The AD807 consumes 140 mW and operates from a single
power supply at either +5 V or –5.2 V.
FUNCTIONAL BLOCK DIAGRAM
PIN
NIN
THRADJ
SDOUT
CLKOUTP
CLKOUTN
DATAOUTP
DATAOUTN
CF1CF2
PRODUCT DESCRIPTION

The AD807 provides the receiver functions of data quantiza-
tion, signal level detect, clock recovery and data retiming for
155 Mbps NRZ data. The device, together with a PIN
diode/preamplifier combination, can be used for a highly inte-
grated, low cost, low power SONET OC-3 or SDH STM-1
fiber optic receiver.
The receiver front end signal level detect circuit indicates when
the input signal level has fallen below a user adjustable thresh-
old. The threshold is set with a single external resistor. The sig-
nal level detect circuit 3 dB optical hysteresis prevents chatter at
the signal level detect output.
The PLL has a factory trimmed VCO center frequency and a
frequency acquisition control loop that combine to guarantee
AD807–SPECIFICATIONS
QUANTIZER–AC CHARACTERISTICS
LEVEL DETECT
PHASE-LOCKED LOOP NOMINAL
JITTER TOLERANCE
POWER SUPPLY CURRENT
SYMMETRY (Duty Cycle)
(TA = TMIN to TMAX, VS = VMIN to VMAX, CD = 0.1 mF, unless otherwise noted)
ABSOLUTE MAXIMUM RATINGS1
SupplyVoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+12V
Input Voltage (Pin 12 or Pin 13) . . . . . . . . . . . . . .VCC + 0.6 V
Maximum Junction Temperature . . . . . . . . . . . . . . . . .+165°C
Storage Temperature Range . . . . . . . . . . . . .–65°C to +150°C
Lead Temperature Range (Soldering10sec) . . . . . . . .+300°C
ESD Rating (Human Body Model) . . . . . . . . . . . . . . . . .500 V
NOTESStresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
Thermal Characteristics:
16-Pin Narrow Body SOIC Package: θJA = 110°C/Watt.
INPUT (V)
OUTPUT

Figure 1.Input Sensitivity, Input Overdrive
DATAOUTP
(PIN 2)
CLKOUTP
(PIN 5)
SETUPHOLD

Figure 2.Setup and Hold Time
PIN FUNCTION DESCRIPTIONS
PIN CONFIGURATION
ORDERING GUIDE
WARNING!
CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD807 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
AD807
DEFINITION OF TERMS
Maximum, Minimum and Typical Specifications

Specifications for every parameter are derived from statistical
analyses of data taken on multiple devices from multiple wafer
lots. Typical specifications are the mean of the distribution of
the data for that parameter. If a parameter has a maximum (or a
minimum), that value is calculated by adding to (or subtracting
from) the mean six times the standard deviation of the distribu-
tion. This procedure is intended to tolerate production varia-
tions: if the mean shifts by 1.5 standard deviations, the remaining
4.5 standard deviations still provide a failure rate of only 3.4 parts
per million. For all tested parameters, the test limits are guard-
banded to account for tester variation to thus guarantee that no
device is shipped outside of data sheet specifications.
Input Sensitivity and Input Overdrive

Sensitivity and Overdrive specifications for the Quantizer in-
volve offset voltage, gain and noise. The relationship between
the logic output of the quantizer and the analog voltage input is
shown in Figure 1.
For sufficiently large positive input voltage the output is always
Logic 1 and similarly, for negative inputs, the output is always
Logic 0. However, the transitions between output Logic Levels
1 and 0 are not at precisely defined input voltage levels, but oc-
cur over a range of input voltages. Within this Zone of Confu-
sion, the output may be either 1 or 0, or it may even fail to attain
a valid logic state. The width of this zone is determined by the
input voltage noise of the quantizer (650 μV at the 1 × 10–10
confidence level). The center of the Zone of Confusion is the
quantizer input offset voltage (±500 μV maximum). Input Over-
drive is the magnitude of signal required to guarantee correct
logic level with 1 × 10–10 confidence level.
With a single-ended PIN-TIA (Figure 3), ac coupling is used
and the inputs to the Quantizer are dc biased at some common-
mode potential. Observing the Quantizer input with an oscillo-
scope probe at the point indicated shows a binary signal with
average value equal to the common-mode potential and instan-
taneous values both above and below the average value. It is
convenient to measure the peak-to-peak amplitude of this signal
and call the minimum required value the Quantizer Sensitivity.
Referring to Figure 1, since both positive and negative offsets
need to be accommodated, the Sensitivity is twice the Over-
drive. The AD807 Quantizer has 2 mV Sensitivity.
With a differential TIA (Figure 3), Sensitivity seems to improve
from observing the Quantizer input with an oscilloscope probe.
This is an illusion caused by the use of a single-ended probe. A
1 mV peak-to-peak signal appears to drive the AD807 Quan-
tizer. However, the single-ended probe measures only half the
signal. The true Quantizer input signal is twice this value since
the other Quantizer input is a complementary signal to the sig-
nal being observed.
Response Time

Response time is the delay between removal of the input signal
and indication of Loss of Signal (LOS) at SDOUT. The re-
sponse time of the AD807 (1.5 μs maximum) is much faster
than the SONET/SDH requirement (3 μs ≤ response time ≤
100 μs). In practice, the time constant of the ac coupling at the
Tracking Range

This is the range of input data rates over which the AD807 will
remain in lock.
Capture Range

This is the range of input data rates over which the AD807 will
acquire lock.
Static Phase Error

This is the steady-state phase difference, in degrees, between the
recovered clock sampling edge and the optimum sampling in-
stant, which is assumed to be halfway between the rising and
falling edges of a data bit. Gate delays between the signals that
define static phase error, and IC input and output signals pro-
hibit direct measurement of static phase error.
Data Transition Density, ρ

This is a measure of the number of data transitions, from “0” to
“1” and from “1” to “0,” over many clock periods. ρ is the ratio
(0 ≤ ρ ≤ 1) of data transitions to bit periods.
Jitter

This is the dynamic displacement of digital signal edges from
their long term average positions, measured in degrees rms or
Unit Intervals (UI). Jitter on the input data can cause dynamic
phase errors on the recovered clock sampling edge. Jitter on the
recovered clock causes jitter on the retimed data.
Output Jitter

This is the jitter on the retimed data, in degrees rms, due to a
specific pattern or some pseudorandom input data sequence
(PRN Sequence).
Jitter Tolerance

Jitter Tolerance is a measure of the AD807’s ability to track a
jittery input data signal. Jitter on the input data is best thought
of as phase modulation, and is usually specified in unit intervals.
The PLL must provide a clock signal that tracks the phase
modulation in order to accurately retime jittered data. In order
for the VCO output to have a phase modulation that tracks the
input jitter, some modulation signal must be generated at the
output of the phase detector. The modulation output from the
phase detector can only be produced by a phase error between
its data input and its clock input. Hence, the PLL can never
perfectly track jittered data. However, the magnitude of the
phase error depends on the gain around the loop. At low fre-
quencies, the integrator of the AD807 PLL provides very high
gain, and thus very large jitter can be tracked with small phase
errors between input data and recovered clock. At frequencies
closer to the loop bandwidth, the gain of the integrator is much
smaller, and thus less input jitter can be tolerated. The AD807
output will have a bit error rate less than 1 × 10–10 when in lock
and retiming input data that has the CCITT G.958 specified
jitter applied to it.
Jitter Transfer (Refer to Figure 20)

The AD807 exhibits a low-pass filter response to jitter applied
to its input data.
Bandwidth

This describes the frequency at which the AD807 attenuates
sinusoidal input jitter by 3 dB.
Damping Factor, ζ
Damping factor, ζ describes the compensation of the second or-
der PLL. A larger value of ζ corresponds to more damping and
less peaking in the jitter transfer function.
Acquisition Time

This is the transient time, measured in bit periods, required for
the AD807 to lock onto input data from its free-running state.
Symmetry—Recovered Clock Duty Cycle

Symmetry is calculated as (100 × on time)/period, where on
time equals the time that the clock signal is greater than the
midpoint between its “0” level and its “1” level.
Bit Error Rate vs. Signal-to-Noise Ratio

AD807 Bit Error Rate vs. Signal-to-Noise Ratio performance is
shown in Figure 11. Wideband amplitude noise is summed with
the input data signal as shown in Figure 4. Performance is
shown for input data levels of 5 mV and 10 mV.
EPITAXX ERM504
VCM
VCM
Single-Ended Input Application
AD8015
DIFFERENTIAL
OUTPUT TIA
VCM
VCM
Differential Input Application
Figure 3. (a–b) Single-Ended and Differential Input
Applications
NOISE
SOURCE100MHz
POWER COMBINER
0.47µF100Ω
GND
AVCC2
DIFFERENTIAL
INPUT
AVEE
CURRENT SOURCES
HEADROOM ≥ 0.7V

a.Quantizer Differential Input Stage
b.Threshold AdjustSignal Detect Output (SDOUT)PLL Differential Output Stage—DATAOUT(N),
CLKOUT(N)
Figure 5.(a–d) Simplified Schematics
AD807–Typical Characteristic Curves
SIGNAL DETECT LEVEL – Volts
200.0E+3
0.0E+0
000.0E+035.0E–35.0E–3
THRESH

10.0E–315.0E–320.0E–325.0E–330.0E–3
180.0E+3
140.0E+3
60.0E+3
40.0E+3
20.0E+3
160.0E+3
120.0E+3
100.0E+3
80.0E+3

Figure 6.Signal Detect Level vs. RTHRESH
TEMPERATURE – °C
35.0E–3
SIGNAL DETECT LEVEL – Volts20406080
30.0E–3
20.0E–3
25.0E–3
15.0E–3
10.0E–3
000.0E+0
5.0E–3

Figure 7.Signal Detect Level vs. Temperature
TEMPERATURE – °C
ELECTRICAL HYSTERESIS – dB20406080
4.00

Figure 8.Signal Detect Hysteresis vs. Temperature
SUPPLY VOLTAGE – Volts
35.000E–3
SIGNAL DETECT LEVEL – Volts
30.000E–3
20.000E–3
25.000E–3
15.000E–3
10.000E–3
000.000E+0
5.000E–3

Figure 9.Signal Detect Level vs. Supply Voltage
POWER SUPPLY – V
ELECTRICAL HYSTERESIS – dB
3.00

Figure 10.Signal Detect Hysteresis vs. Power Supply
1E-5
1E-10
1E-21216182224
1E-3
1E-4
1E-8
1E-6
1E-1
5E-2
3E-2
2E-2
BIT ERROR RATE
S/N – dB20
1E-12

Figure 11.Bit Error Rate vs. Signal-to-Noise Ratio
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED