IC Phoenix
 
Home ›  AA15 > AD7819YN-AD7819YR-AD7819YRU,+2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADC
AD7819YN-AD7819YR-AD7819YRU Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
AD7819YNADN/a5avai+2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADC
AD7819YRADN/a300avai+2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADC
AD7819YRUADN/a95avai+2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADC


AD7819YR ,+2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADCCHARACTERISTICS (–40C to +125C, unless otherwise noted)Parameter V = 3 V  10% V = 5 V  10% Unit ..
AD7819YRU ,+2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADCGENERAL DESCRIPTION1. Low Power, Single Supply OperationThe AD7819 is a high speed, microprocessor- ..
AD7819YRUZ ,+2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADCSPECIFICATIONSParameter Y Version Unit Test Conditions/CommentsDYNAMIC PERFORMANCE f = 30 kHz, f = ..
AD781AN ,Complete 700 ns Sample-and-Hold AmplifierFEATURESAcquisition Time to 0.01%: 700 ns MaximumLow Power Dissipation: 95 mW1 8V OUTCCLow Droop Ra ..
AD781JN ,Complete 700 ns Sample-and-Hold AmplifierSPECIFICATIONSAD781J AD781A AD781SParameter Min Typ Max Min Typ Max Min Typ Max UnitsTOTAL HARMONIC ..
AD7820KN ,LC2MOS HIGH-SPEED uP-COMPATIBLE 8-BIT ADC WITH TRACK/HOLD FUNCTIONFEATURES Fast Conversion Time: 1.36pa max BuiIt-ln Trattk-artd-Hoid Function No Missed Cod ..
ADM208AN ,0.1 uF, +5 V Powered CMOS RS-232 Drivers/ReceiversSpecifications T to T unless otherwise noted.)MIN MAXParameter Min Typ Max Units Test Conditions/Co ..
ADM208AR ,0.1 uF, +5 V Powered CMOS RS-232 Drivers/ReceiversSPECIFICATIONS211, 213); V = +5 V 6 5% (ADM205);CCV+ = +9 V to +13.2 V (ADM209); C1–C4 = 0.1 mF Cer ..
ADM208AR ,0.1 uF, +5 V Powered CMOS RS-232 Drivers/ReceiversGENERAL DESCRIPTION active-high receiver enable control. Two receivers of theThe ADM2xx family of l ..
ADM208AR ,0.1 uF, +5 V Powered CMOS RS-232 Drivers/ReceiversSpecifications T to T unless otherwise noted.)MIN MAXParameter Min Typ Max Units Test Conditions/Co ..
ADM208AR-REEL , 0.1 muF, 5 V Powered CMOS RS-232 Drivers/Receivers
ADM208ARS ,0.1 uF, +5 V Powered CMOS RS-232 Drivers/ReceiversSPECIFICATIONS211, 213); V = +5 V 6 5% (ADM205);CCV+ = +9 V to +13.2 V (ADM209); C1–C4 = 0.1 mF Cer ..


AD7819YN-AD7819YR-AD7819YRU
+2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADC
REV.A
+2.7 V to +5.5 V, 200 kSPS
8-Bit Sampling ADC
FUNCTIONAL BLOCK DIAGRAM
FEATURES
8-Bit ADC with 4.5 �s Conversion Time
On-Chip Track and Hold
Operating Supply Range: +2.7 V to +5.5 V
Specifications at +2.7 V – 3.6 V and 5 V � 10%
8-Bit Parallel Interface
8-Bit Read
Power Performance
Normal Operation
10.5 mW, VDD = 3 V
Automatic Power-Down
57.75 �W @ 1 kSPS, VDD = 3 V
Analog Input Range: 0 V to VREF
Reference Input Range: 1.2 V to VDD
GENERAL DESCRIPTION

The AD7819 is a high speed, microprocessor-compatible, 8-bit
analog-to-digital converter with a maximum throughput of
200 kSPS. The converter operates off a single +2.7 V to +5.5 V
supply and contains a 4.5 µs successive approximation A/D
converter, track/hold circuitry, on-chip clock oscillator and 8-bit
wide parallel interface. The parallel interface is designed to
allow easy interfacing to microprocessors and DSPs. Using only
address decoding logic the AD7819 is easily mapped into the
microprocessor address space.
When used in its power-down mode, the AD7819 automatically
powers down at the end of a conversion and powers up at the
start of a new conversion. This feature significantly reduces the
power consumption of the part at lower throughput rates. The
AD7819 can also operate in a high speed mode where the part is
not powered down between conversions. In this mode of opera-
tion the part is capable of providing 200 kSPS throughput.
The part is available in a small, 16-pin 0.3" wide, plastic dual-
in-line package (DIP); in a 16-pin, 0.15" wide, narrow body
small outline IC (SOIC) and in a 16-pin, narrow body, thin
shrink small outline package (TSSOP).
PRODUCT HIGHLIGHTS
Low Power, Single Supply Operation
The AD7819 operates from a single +2.7 V to +5.5 V sup-
ply and typically consumes only 10.5 mW of power. The
power dissipation can be significantly reduced at lower
throughput rates by using the automatic power-down mode.Automatic Power-Down
The automatic power-down mode, whereby the AD7819
goes into power-down mode at the end of a conversion and
powers up before the next conversion, means the AD7819
is ideal for battery powered applications; e.g., 57.75 µW
@ 1 kSPS. (See Power vs. Throughput Rate section.)Parallel Interface
An easy to use 8-bit wide parallel interface allows interfacing
to most popular microprocessors and DSPs with minimal
external circuitry.Dynamic Specifications for DSP Users
In addition to the traditional ADC specifications, the AD7819
is specified for ac parameters, including signal-to-noise ratio
and distortion.
AD7819–SPECIFICATIONS1(GND = 0 V, VREF = +VDD = 3 V � 10% to 5 V � 10%). All specifications –40�C
to +125�C unless otherwise noted.)

DC ACCURACY
NOTESSee Terminology section.
TIMING CHARACTERISTICS1, 2
tPOWER-UP
NOTES
1Sample tested to ensure compliance.
2See Figures 12, 13 and 14.
3These numbers are measured with the load circuit of Figure 1. They are defined as the time required for the o/p to cross 0.8 V or 2.4 V for VDD = 5 V ± 10% and
0.4 V or 2 V for VDD = 3 V ± 10%.
4Derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated back
to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t7, quoted in the Timing Characteristics is the true bus relinquish time
of the part and as such is independent of external bus loading capacitances.
Specifications subject to change without notice.
(–40�C to +125�C, unless otherwise noted)
ABSOLUTE MAXIMUM RATINGS*

VDD to DGND . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Input Voltage to DGND
(CONVST, RD, CS)
Digital Output Voltage to DGND
(BUSY, DB0–DB7)
REFIN to AGND . . . . . . . . . . . . . . . . . . .–0.3 V, VDD + 0.3 V
Analog Input . . . . . . . . . . . . . . . . . . . . . .–0.3 V, VDD + 0.3 V
Storage Temperature Range . . . . . . . . . . . .–65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
Plastic DIP Package, Power Dissipation . . . . . . . . . .450 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . .+105°C/W
Lead Temperature, (Soldering 10 sec) . . . . . . . . . . .+260°C
SOIC Package, Power Dissipation . . . . . . . . . . . . . . .450 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . .75°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . .+215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . .+220°C
SSOP Package, Power Dissipation . . . . . . . . . . . . . . .450 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . .115°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . .+215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . .+220°C
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .≤4 kV
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
Figure 1.Load Circuit for Digital Output Timing
Specifications
ORDERING GUIDE
AD7819
PIN FUNCTION DESCRIPTIONS
PIN CONFIGURATION
DIP/SOIC
TERMINOLOGY
Signal to (Noise + Distortion) Ratio

This is the measured ratio of signal to (noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (fS/2), excluding dc.
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the quan-
tization noise. The theoretical signal to (noise + distortion)
ratio for an ideal N-bit converter with a sine wave input is given
by:
Signal to (Noise + Distortion) = (6.02N + 1.76) dB
Thus for an 8-bit converter, this is 50dB.
Total Harmonic Distortion

Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7819 it is defined as:
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5 and V6 are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise

Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is deter-
mined by the largest harmonic in the spectrum, but for parts
where the harmonics are buried in the noise floor, it will be a
noise peak.
Intermodulation Distortion

With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa ± nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation terms are those for which
neither m nor n are equal to zero. For example, the second order
terms include (fa + fb) and (fa – fb), while the third order terms
include (2fa + fb), (2fa – fb), (fa + 2fb) and (fa – 2fb).
The AD7819 is tested using the CCIF standard, where two
input frequencies near the top end of the input bandwidth are
used. In this case, the second and third order terms are of differ-
ent significance. The second order terms are usually distanced
in frequency from the original sine waves, while the third order
terms are usually at a frequency close to the input frequencies.
As a result, the second and third order terms are specified sepa-
rately. The calculation of the intermodulation distortion is as
per the THD specification where it is the ratio of the rms sum of
the individual distortion products to the rms amplitude of the
fundamental expressed in dBs.
Relative Accuracy

Relative accuracy or endpoint nonlinearity is the maximum
deviation from a straight line passing through the endpoints of
the ADC transfer function.
Differential Nonlinearity

This is the difference between the measured and the idealLSB change between any two adjacent codes in the ADC.
Offset Error

This is the deviation of the first code transition (0000...000)
to (0000...001) from the ideal, i.e., AGND + 1 LSB.
Offset Error Match

This is the difference in Offset Error between any two channels.
Gain Error

This is the deviation of the last code transition (1111...110)
to (1111...111) from the ideal, i.e., VREF – 1 LSB, after the
offset error has been adjusted out.
Gain Error Match

This is the difference in Gain Error between any two channels.
Track/Hold Acquisition Time

Track/hold acquisition time is the time required for the output
of the track/hold amplifier to reach its final value, within1/2 LSB, after the end of conversion (the point at which the
track/hold returns to track mode). It also applies to situations
where a change in the selected input channel takes place or
where there is a step input change on the input voltage applied
to the selected VIN input of the AD7819. It means that the user
must wait for the duration of the track/hold acquisition time
after the end of conversion or after a step input change to VIN
before starting another conversion, to ensure that the part
operates to specification.
AD7819
CIRCUIT DESCRIPTION
Converter Operation

The AD7819 is a successive approximation analog-to-digital
converter based around a charge redistribution DAC. The ADC
can convert analog input signals in the range 0 V to VDD. Fig-
ures 2 and 3 below show simplified schematics of the ADC.
Figure 2 shows the ADC during its acquisition phase. SW2 is
closed and SW1 is in Position A, the comparator is held in a
balanced condition and the sampling capacitor acquires the sig-
nal on VIN+.
Figure 2.ADC Track Phase
When the ADC starts a conversion, see Figure 3, SW2 will open
and SW1 will move to Position B causing the comparator to
become unbalanced. The Control Logic and the Charge Redis-
tribution DAC are used to add and subtract fixed amounts of
charge from the sampling capacitor to bring the comparator
back into a balanced condition. When the comparator is rebal-
anced the conversion is complete. The Control Logic generates
the ADC output code. Figure 7 shows the ADC transfer function.
Figure 3.ADC Conversion Phase
TYPICAL CONNECTION DIAGRAM

Figure 4 shows a typical connection diagram for the AD7819. The
parallel interface is implemented using an 8-bit data bus, the
falling edge of CONVST brings the BUSY signal high and at
the end of conversion, the falling edge of BUSY is used to
initiate an ISR on a microprocessor. (See Parallel Interface
section for more details.) VREF is connected to a well decoupled
VDD pin to provide an analog input range of 0 V to VDD. When
VDD is first connected the AD7819 powers up in a low current
mode, i.e., power down. A rising edge on the CONVST input
will cause the part to power up. (See Power-Up Times section.)
If power consumption is of concern, the automatic power-down
at the end of a conversion should be used to improve power
performance. See Power vs. Throughput Rate section of the
data sheet.
Figure 4.Typical Connection Diagram
Analog Input

Figure 5 shows an equivalent circuit of the analog input struc-
ture of the AD7819. The two diodes, D1 and D2, provide ESD
protection for the analog inputs. Care must be taken to ensure
that the analog input signal never exceeds the supply rails by
more than 200 mV. This will cause these diodes to become
forward biased and start conducting current into the substrate.
20 mA is the maximum current these diodes can conduct with-
out causing irreversible damage to the part. The capacitor C2
is typically about 4 pF and can be primarily attributed to pin
capacitance. The resistor R1 is a lumped component made up of
the on resistance of a multiplexer and a switch. This resistor is
typically about 125 Ω. The capacitor C1 is the ADC sampling
capacitor and has a capacitance of 3.5 pF.
Figure 5.Equivalent Analog Input Circuit
DC Acquisition Time

The ADC starts a new acquisition phase at the end of a conver-
sion and ends on the falling edge of the CONVST signal. At the
end of a conversion there is a settling time associated with the
sampling circuit. This settling time lasts approximately 100 ns.
The analog signal on VIN is also being acquired during this
settling time. The minimum acquisition time needed is approxi-
mately 100 ns. Figure 6 shows the equivalent charging circuit
for the sampling capacitor when the ADC is in its acquisition
phase. R2 represents the source impedance of a buffer amplifier
or resistive network, R1 is an internal multiplexer resistance and
C1 is the sampling capacitor.
Figure 6.Equivalent Sampling Circuit
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED