IC Phoenix
 
Home ›  AA15 > AD7711AN-AD7711AR,LC2MOS Signal Conditioning ADC with RTD Excitation Currents
AD7711AN-AD7711AR Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
AD7711ANN/a64avaiLC2MOS Signal Conditioning ADC with RTD Excitation Currents
AD7711ARADN/a580avaiLC2MOS Signal Conditioning ADC with RTD Excitation Currents


AD7711AR ,LC2MOS Signal Conditioning ADC with RTD Excitation Currentsfeatures one differential analog input and one singlePRODUCT HIGHLIGHTSended analog input as well a ..
AD7712AN ,LC2MOS Signal Conditioning ADCspecifications T to T unless otherwise noted.)MIN MAX1Parameter A, S Versions Units Conditions/Comm ..
AD7712AQ ,LC2MOS Signal Conditioning ADCFEATURESFUNCTIONAL BLOCK DIAGRAMCharge Balancing ADCREF REFDV V24 Bits No Missing Codes AVDD DD IN ..
AD7712AR ,LC2MOS Signal Conditioning ADCapplications with an on-chip control register that allowsinput signals on the low level analog inpu ..
AD7712AR ,LC2MOS Signal Conditioning ADCGENERAL DESCRIPTIONport. The AD7712 also contains self-calibration, system calibra-The AD7712 is a ..
AD7713AN ,LC2MOS Loop-Powered Signal Conditioning ADCapplications with an on-chip control register which allowscan be configured in software using the b ..
ADM1031ARQZ-REEL ,Complete, ACPI Compliant, Dual Channel ±1°C Remote Thermal Monitor with Integrated Fan Controller for two Independent Fans, ...Specifications subject to change without notice.–2– REV. AADM1031ABSOLUTE MAXIMUM RATINGS* ORDERING ..
ADM1032AR ,+-1C Remote and Local System Temperature MonitorSPECIFICATIONS (T = T to T , V = V to V , unless otherwise noted.)A MIN MAX DD MIN MAXParameter Min ..
ADM1032AR-1 ,High Accuracy, Remote Thermal Diode Monitor in Micro SOIC PackageSPECIFICATIONSParameter Min Typ Max Unit Test Conditions/CommentsPOWER SUPPLYSupply Voltage, V 3.0 ..
ADM1032ARM ,+-1C Remote and Local System Temperature MonitorSpecifications subject to change without notice.–2– REV. 0ADM1032ABSOLUTE MAXIMUM RATINGS* THERMAL
ADM1032ARM-1 ,High Accuracy, Remote Thermal Diode Monitor in Micro SOIC PackageAPPLICATIONSThis output can be used as an interrupt or as an SMBus alert.Desktop and Notebook Compu ..
ADM1032ARM-REEL ,High Accuracy, Remote Thermal Diode Monitor in Micro SOIC PackageSPECIFICATIONSParameter Min Typ Max Unit Test Conditions/CommentsPOWER SUPPLYSupply Voltage, V 3.0 ..


AD7711AN-AD7711AR
LC2MOS Signal Conditioning ADC with RTD Excitation Currents
FUNCTIONAL BLOCK DIAGRAMFEATURES
Charge Balancing ADC
24 Bits No Missing Codes

60.0015% Nonlinearity
Two-Channel Programmable Gain Front End
Gains from 1 to 128
One Differential Input
One Single-Ended Input
Low-Pass Filter with Programmable Filter Cutoffs
Ability to Read/Write Calibration Coefficients
RTD Excitation Current Sources
Bidirectional Microcontroller Serial Interface
Internal/External Reference Option
Single or Dual Supply Operation
Low Power (25 mW typ) with Power-Down Mode
(7 mW typ)
APPLICATIONS
RTD Transducers
Process Control
Smart Transmitters
Portable Industrial Instruments2MOS Signal Conditioning ADC
with RTD Excitation Currents

REV.F
GENERAL DESCRIPTION

The AD7711 is a complete analog front end for low frequency
measurement applications. The device accepts low level signals
directly from a transducer and outputs a serial digital word. It
employs a sigma-delta conversion technique to realize up to
24 bits of no missing codes performance. The input signal is
applied to a proprietary programmable gain front end based
around an analog modulator. The modulator output is pro-
cessed by an on-chip digital filter. The first notch of this digital
filter can be programmed via the on-chip control register allow-
ing adjustment of the filter cutoff and settling time.
The part features one differential analog input and one single
ended analog input as well as a differential reference input.
Normally, one of the input channels will be used as the main
channel with the second channel used as an auxiliary input to
periodically measure a second voltage. It can be operated from a
single supply (by tying the VSS pin to AGND) provided that the
input signals on the analog inputs are more positive than
–30mV. By taking the VSS pin negative, the part can convert
signals down to –VREF on its inputs. The part provides two
current sources that can be used to provide excitation in three-
wire and four-wire RTD configurations. The AD7711 thus
performs all signal conditioning and conversion for a single or
dual channel system.
The AD7711 is ideal for use in smart, microcontroller based
systems. Gain settings, signal polarity, input channel selection
and RTD current control can be configured in software using
the bidirectional serial port. The AD7711 contains self-
calibration, system calibration and background calibration
options and also allows the user to read and write the on-chip
calibration registers.
CMOS construction ensures low power dissipation, and a soft-
ware programmable power-down mode reduces the standby
power consumption to only 7 mW typical. The part is available
in a 24-lead, 0.3 inch wide, plastic and hermetic dual-in-line
package (DIP) as well as a 24-lead small outline (SOIC)
package.
PRODUCT HIGHLIGHTS
The programmable gain front end allows the AD7711 to
accept input signals directly from an RTD transducer,
removing a considerable amount of signal conditioning.
On-chip current sources provide excitation for three-wire and
four-wire RTD configurations.No Missing Codes ensure true, usable, 23-bit dynamic range
coupled with excellent –0.0015% accuracy. The effects of
temperature drift are eliminated by on-chip self-calibration,
which removes zero-scale and full-scale errors.The AD7711 is ideal for microcontroller or DSP processor
applications with an on-chip control register which allows
control over filter cutoff, input gain, channel selection, signal
polarity, RTD current control and calibration modes.The AD7711 allows the user to read and to write the on-chip
calibration registers. This means that the microcontroller has
much greater control over the calibration procedure.
*Protected by U.S. Patent No. 5,134,401.
NOTESTemperature range is as follows: A Version = –40°C to +85°C; S Version = –55°C to +125°C. See also Note 16.Applies after calibration at the temperature of interest.Positive full-scale error applies to both unipolar and bipolar input ranges.These errors will be of the order of the output noise of the part as shown in Table I after system calibration. These errors will be 20 mV typical after self-calibration or
background calibration.Recalibration at any temperature or use of the background calibration mode will remove these drift errors.These numbers are guaranteed by design and/or characterization.This common-mode voltage range is allowed, provided that the input voltage on AIN(+) and AIN(–) does not exceed AVDD + 30 mV and VSS – 30 mV.The analog inputs present a very high impedance dynamic load which varies with clock frequency and input sample rate. The maximum recommended source
resistance depends on the selected gain (see Tables IV and V).The analog input voltage range on the AIN1(+) input is given here with respect to the voltage on the AIN1(–) input. The input voltage range on the AIN2 input is
AD7711–SPECIFICATIONS
(AVDD = +5␣V
6 5%; DVDD = +5␣V 6 5%; VSS = 0␣V or –5V 6 5%; REF IN(+) =
+2.5␣V; REF␣IN(–) = AGND; MCLK IN = 10␣MHz unless otherwise stated. All specifications TMIN to TMAX unless otherwise noted.)
VBIAS INPUT
LOGIC OUTPUTS
SYSTEM CALIBRATION
NOTESThe AD7711 is tested with the following VBIAS voltages. With AVDD = +5 V and VSS = 0 V, VBIAS = +2.5 V; with AVDD = +10 V and VSS = 0 V, VBIAS = +5 V and
with AVDD = +5 V and VSS = –5 V, VBIAS = 0 V.Guaranteed by design, not production tested.After calibration, if the analog input exceeds positive full scale, the converter will output all 1s. If the analog input is less than negative full scale, then the device will
output all 0s.These calibration and span limits apply provided the absolute voltage on the analog inputs does not exceed AVDD + 30 mV or go more negative than VSS – 30 mV.
The offset calibration limit applies to both the unipolar zero point and the bipolar zero point.
AD7711
ORDERING GUIDE
*N = Plastic DIP, Q = Cerdip; R = SOIC.
POWER REQUIREMENTS
NOTESThe AD7711 is specified with a 10 MHz clock for AVDD voltages of +5 V – 5%. It is specified with an 8 MHz clock for AVDD voltages greater than 5.25 V and less
than 10.5V.The –5% tolerance on the DVDD input is allowed provided that DVDD does not exceed AVDD by more than 0.3 V.Measured at dc and applies in the selected passband. PSRR at 50 Hz will exceed 120 dB with filter notches of 10 Hz, 25 Hz or 50 Hz. PSRR at 60 Hz will exceed
120 dB with filter notches of 10 Hz, 30 Hz or 60 Hz.PSRR depends on gain: Gain of 1 = 70 dB typ; Gain of 2: 75 dB typ; Gain of 4 = 80 dB typ; Gains of 8 to 128 = 85 dB typ. These numbers can be improved (to
95 dB typ) by deriving the VBIAS voltage (via Zener diode or reference) from the AVDD supply.
Specifications subject to change without notice.
AD7711–SPECIFICATIONS

REF OUT to AGND . . . . . . . . . . . . . . . . . . . .–0.3 V to AVDD
Digital Input Voltage to DGND . . . . .–0.3 V to AVDD + 0.3 V
Digital Output Voltage to DGND . . . –0.3 V to DVDD + 0.3 V
Operating Temperature Range
Commercial (A Version) . . . . . . . . . . . . . . . .–40°C to +85°C
Extended (S Version) . . . . . . . . . . . . . . . . .–55°C to +125°C
Storage Temperature Range . . . . . . . . . . . . .–65°C to +150°C
Lead Temperature (Soldering, 10 secs) . . . . . . . . . . . .+300°C
Power Dissipation (Any Package) to +75°C . . . . . . . .450 mW
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of the specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
ABSOLUTE MAXIMUM RATINGS*

(TA = +25°C, unless otherwise noted)
AVDD to DVDD . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +12 V
AVDD to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +12 V
AVDD to AGND . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +12 V
AVDD to DGND . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +12 V
DVDD to AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
DVDD to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
VSS to AGND . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –6 V
VSS to DGND . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –6 V
Analog Input Voltage to AGND
. . . . . . . . . . . . . . . . . . . . . . . . . VSS – 0.3 V to AVDD + 0.3 V
Reference Input Voltage to AGND
. . . . . . . . . . . . . . . . . . . . . . . . . VSS – 0.3 V to AVDD + 0.3 V
CAUTION

ESD (electrostatic discharge) sensitive device. The digital control inputs are diode protected;
however, permanent damage may occur on unconnected devices subject to high energy electro-
static fields. Unused devices must be stored in conductive foam or shunts. The protective foam
should be discharged to the destination socket before devices are inserted.
TIMING CHARACTERISTICS1, 2
(DVDD = +5␣V 6 5%; AVDD = +5␣V or +10 V3 6 5%; VSS = 0 V or –5 V 6 10%; AGND = DGND =
0 V; fCLK IN = 10␣MHz; Input Logic 0 = 0 V, Logic 1 = DVDD, unless otherwise noted.)
AD7711
NOTESGuaranteed by design, not production tested. All input signals are specified with tr = tf = 5 ns (10% to 90% of 5 V) and timed from a voltage level of 1.6 V.See Figures 10 to 13.The AD7711 is specified with a 10 MHz clock for AVDD voltages of +5 V – 5%. It is specified with an 8 MHz clock for AVDD voltages greater than 5.25V and less
than 10.5V.CLK IN duty cycle range is 45% to 55%. CLK IN must be supplied whenever the AD7711 is not in STANDBY mode. If no clock is present in this case, the device
can draw higher current than specified and possibly become uncalibrated.The AD7711 is production tested with fCLK IN at 10 MHz (8 MHz for AVDD > +5.25 V). It is guaranteed by characterization to operate at 400kHz.Specified using 10% and 90% points on waveform of interest.These numbers are measured with the load circuit of Figure 1 and defined as the time required for the output to cross 0.8 V or 2.4 V.These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then
extrapolated back to remove effects of charging or discharging the 100 pF capacitor. This means that the times quoted in the timing characteristics are the true bus
relinquish times of the part and, as such, are independent of external bus loading capacitances.
Specifications subject to change without notice.
Figure 1.Load Circuit for Access Time and Bus Relinquish
Time
PIN CONFIGURATION
DIP AND SOIC
PIN FUNCTION DESCRIPTION
AD7711
TERMINOLOGY
INTEGRAL NONLINEARITY

This is the maximum deviation of any code from a straight line
passingthroughtheendpointsofthetransferfunction. The end-
points of the transfer function are zero-scale (not to be confused
withbipolarzero),apoint0.5LSBbelowthefirstcode transi-
tion (000...000 to 000...001) and full scale, a point 0.5LSB
abovethelastcodetransition(111...110to 111...111). The
error is expressed as a percentage of full scale.
POSITIVE FULL-SCALE ERROR

Positive full-scale error is the deviation of the last code transi-
tion (111...110 to 111...111) from the ideal input full-scale
voltage. For AIN1(+), the ideal full-scale input voltage is
(AIN1(–) + VREF/GAIN – 3/2 LSBs); for AIN2, the ideal full-
scale input voltage is VREF/GAIN – 3/2 LSBs. It applies to both
unipolar and bipolar analog input ranges.
UNIPOLAR OFFSET ERROR

Unipolar offset error is the deviation of the first code transition
from the ideal voltage. For AIN1(+), the ideal input voltage is
(AIN1(–) + 0.5 LSB); for AIN2, the ideal input is 0.5 LSB
when operating in the unipolar mode.
BIPOLAR ZERO ERROR

This is the deviation of the midscale transition (0111...111
to 1000...000) fromtheideal input voltage. For AIN1(+), the
ideal input voltage is (AIN1(–)– 0.5LSB); for AIN2, the ideal
input is – 0.5 LSB when operating in the bipolar mode.
BIPOLAR NEGATIVE FULL-SCALE ERROR

This is the deviation of the first code transition from the ideal
input voltage. For (AIN1(+), the ideal input voltage is (AIN1(–)
– VREF/GAIN + 0.5 LSB); for AIN2 the ideal input is – VREF/
GAIN + 0.5 LSB when operating in the bipolar mode.
POSITIVE FULL-SCALE OVERRANGE

Positive full-scale overrange is the amount of overhead available
to handle input voltages on AIN1(+) input greater than
AIN1(–) + VREF/GAIN or on the AIN2 input greater than +
VREF/GAIN (for example, noise peaks or excess voltages due to
system gain errors in system calibration routines) without intro-
ducing errors due to overloading the analog modulator or to
overflowing the digital filter.
NEGATIVE FULL-SCALE OVERRANGE

This is the amount of overhead available to handle voltages on
AIN1(+) below AIN1(–) – VREF/GAIN or on AIN2 below
–VREF/GAIN without overloading the analog modulator or over-
flowing the digital filter. Note that the analog input will accept
negative voltage peaks on AIN1(+) even in the unipolar mode
provided that AIN1(+) is greater than AIN1(–) and greater than
VSS – 30␣mV.
OFFSET CALIBRATION RANGE

In the system calibration modes, the AD7711 calibrates its
offset with respect to the analog input. The offset calibration
range specification defines the range of voltages that the
AD7711 can accept and still calibrate offset accurately.
FULL-SCALE CALIBRATION RANGE

This is the range of voltages that the AD7711 can accept in the
system calibration mode and still calibrate full-scale correctly.
INPUT SPAN

In system calibration schemes, two voltages applied in sequence
to the AD7711’s analog input define the analog input range.
The input span specification defines the minimum and maxi-
mum input voltages from zero to full-scale that the AD7711
can accept and still calibrate gain accurately.
CONTROL REGISTER (24 BITS)
A write to the device with the A0 input low writes data to the control register. A read to the device with the A0 input low accesses the
contents of the control register. The control register is 24-bits wide and when writing to the register 24 bits of data must be written
otherwise the data will not be loaded to the control register. In other words, it is not possible to write just the first 12-bits of data into
the control register. If more than 24 clock pulses are provided before TFS returns high, then all clock pulses after the 24th clock
pulse are ignored. Similarly, a read operation from the control register should access 24 bits of data.
MSB
LSB

AD7711
PGA GainGlG0Gain
001(Default Condition After the Internal Power-On Reset)
Channel SelectionChannelAIN1(Default Condition After the Internal Power-On Reset)AIN2
Power-Down
Normal Operation(Default Condition After the Internal Power-On Reset)Power-Down
Word LengthOutput Word Length
16-bit(Default Condition After Internal Power-On Reset)24-bit
RTD Excitation Current
Off(Default Condition After Internal Power-On Reset)
1On
Burnout Current
Off(Default Condition After Internal Power-On Reset)
1On
Bipolar/Unipolar Selection (Both Inputs)
B/U
Bipolar(Default Condition After Internal Power-On Reset)Unipolar
Filter Selection (FS11–FS0)

The on-chip digital filter provides a Sinc3 (or (Sinx/x)3) filter response. The 12 bits of data programmed into these bits determine
the filter cutoff frequency, the position of the first notch of the filter and the data rate for the part. In association with the gain selec-
tion, it also determines the output noise (and hence the effective resolution) of the device.
The first notch of the filter occurs at a frequency determined by the relationship: filter first notch frequency = (fCLK IN/512)/code
where code is the decimal equivalent of the code in bits FS0 to FS11 and is in the range 19 to 2,000. With the nominal fCLK IN of
10 MHz, this results in a first notch frequency range from 9.76 Hz to 1.028 kHz. To ensure correct operation of the AD7711, the
value of the code loaded to these bits must be within this range. Failure to do this will result in unspecified operation of the device.
Changing the filter notch frequency, as well as the selected gain, impacts resolution. Tables I and II and Figure 2 show the effect of
the filter notch frequency and gain on the effective resolution of the AD7711. The output data rate (or effective conversion time) for
the device is equal to the frequency selected for the first notch of the filter. For example, if the first notch of the filter is selected at
50 Hz, then a new word is available at a 50 Hz rate or every 20 ms. If the first notch is at 1 kHz, a new word is available every 1 ms.
The settling time of the filter to a full-scale step input change is worst case 4 · 1/(output data rate). This settling time is to 100% of
the final value. For example, with the first filter notch at 50 Hz, the settling time of the filter to a full-scale step input change is
80 ms max. If the first notch is at 1 kHz, the settling time of the filter to a full-scale input step is 4 ms max. This settling time can be
reduced to 3 · 1/(output data rate) by synchronizing the step input change to a reset of the digital filter. In other words, if the step
input takes place with SYNC low, the settling time will be 3 · 1/(output data rate). If a change of channels takes place, the settling
time is 3 · 1/(output data rate) regardless of the SYNC input.
The –3 dB frequency is determined by the programmed first notch frequency according to the relationship: filter –3 dB frequency
Tables I and II show the output rms noise for some typical notch and –3 dB frequencies. The numbers given are for the bipolar
input ranges with a VREF of +2.5 V. These numbers are typical and are generated with an analog input voltage of 0 V. The output
noise from the part comes from two sources. The first is the electrical noise in the semiconductor devices used in the implementation
of the modulator (device noise). The second occurs when the analog input signal is converted into the digital domain adding quanti-
zation noise. The device noise is at a low level and is largely independent of frequency. The quantization noise starts at an even
lower level but rises rapidly with increasing frequency to become the dominant noise source. Consequently, lower filter notch set-
tings (below 60 Hz approximately) tend to be device noise dominated while higher notch settings are dominated by quantization
noise. Changing the filter notch and cutoff frequency in the quantization noise dominated region results in a more dramatic im-
provement in noise performance than it does in the device noise dominated region as shown in Table I. Furthermore, quantization
noise is added after the PGA, so effective resolution is independent of gain for the higher filter notch frequencies. Meanwhile, device
noise is added in the PGA and, therefore, effective resolution suffers a little at high gains for lower notch frequencies.
At the lower filter notch settings (below 60 Hz), the no missing codes performance of the device is at the 24-bit level. At the higher
settings, more codes will be missed until at 1 kHz notch setting, no missing codes performance is only guaranteed to the 12-bit level.
However, since the effective resolution of the part is 10.5 bits for this filter notch setting, this no missing codes performance should
be more than adequate for all applications.
The effective resolution of the device is defined as the ratio of the output rms noise to the input full scale. This does not remain
constant with increasing gain or with increasing bandwidth. Table II shows the same table as Table I except that the output is now
expressed in terms of effective resolution (the magnitude of the rms noise with respect to 2 · VREF/GAIN, i.e., the input full scale). It
is possible to do post filtering on the device to improve the output data rate for a given –3 dB frequency and also to further reduce
the output noise (see Digital Filtering section).
Table I.Output Noise vs. Gain and First Notch Frequency

10␣
NOTESThe default condition (after the internal power-on reset) for the first notch of filter is 60 Hz.For these filter notch frequencies, the output rms noise is primarily dominated by device noise and as a result is independent of the value of the reference voltage.
Therefore, increasing the reference voltage will give an increase in the effective resolution of the device (i.e., the ratio of the rms noise to the input full scale is in-
creased since the output rms noise remains constant as the input full scale increases).For these filter notch frequencies, the output rms noise is dominated by quantization noise and as a result is proportional to the value of the reference voltage.
Table II.Effective Resolution vs. Gain and First Notch Frequency
Filter and O/P

NOTEEffective resolution is defined as the magnitude of the output rms noise with respect to the input full scale (i.e., 2 · VREF/GAIN). The above table applies for
a VREF of +2.5 V and resolution numbers are rounded to the nearest 0.5 LSB.
AD7711
Figure 2 gives similar information to that outlined in Table I. In this plot, the output rms noise is shown for the full range of available
cutoffs frequencies rather than for some typical cutoff frequencies as in Tables I and II. The numbers given in these plots are typical
values at 25°C.
Figure 2a.Plot of Output Noise vs. Gain and Notch
Frequency (Gains of 1 to 8)
CIRCUIT DESCRIPTION

The AD7711 is a sigma-delta A/D converter with on-chip digital
filtering, intended for the measurement of wide dynamic range,
low frequency signals such as those in RTD applications, indus-
trial control or process control applications. It contains a sigma-
delta (or charge-balancing) ADC, a calibration microcontroller
with on-chip static RAM, a clock oscillator, a digital filter and a
bidirectional serial communications port.
The part contains two analog input channels, a programmable
gain differential analog input and a programmable gain single
ended input. The gain range is from 1 to 128 allowing the part
to accept unipolar signals of between 0 mV to +20 mV and 0 V
to +2.5 V or bipolar signals in the range from –20 mV to –2.5 V
when the reference input voltage equals +2.5 V. The input
signal to the selected analog input channel is continuously
sampled at a rate determined by the frequency of the master
clock, MCLK IN, and the selected gain (see Table III). A
charge balancing A/D converter (Sigma-Delta Modulator) con-
verts the sampled signal into a digital pulse train whose duty
cycle contains the digital information. The programmable gain
function on the analog input is also incorporated in this sigma-
delta modulator with the input sampling frequency being modi-
fied to give the higher gains. A sinc3 digital low-pass filter
processes the output of the sigma-delta modulator and updates
the output register at a rate determined by the first notch fre-
quency of this filter. The output data can be read from the serial
port randomly or periodically at any rate up to the output regis-
ter update rate. The first notch of this digital filter (and hence
its –3 dB frequency) can be programmed via an on-chip control
register. The programmable range for this first notch frequency
is from 9.76 Hz to 1.028 kHz, giving a programmable range for
the –3 dB frequency of 2.58 Hz to 269 Hz.
The basic connection diagram for the part is shown in Figure 3.
This shows the AD7711 in the external clocking mode with
Figure 2b.Plot of Output Noise vs. Gain and Notch
Frequency (Gains of 16 to 128)
separate supplies for both AVDD and DVDD, and in some of
these cases, the analog supply will exceed the +5 V digital sup-
ply (see Power Supplies and Grounding section).
Figure 3.Basic Connection Diagram
The AD7711 provides a number of calibration options which
can be programmed via the on-chip control register. A calibra-
tion cycle may be initiated at any time by writing to this control
register. The part can perform self-calibration using the on-chip
calibration microcontroller and SRAM to store calibration pa-
rameters. Other system components may also be included in the
calibration loop to remove offset and gain errors in the input
channel using the system calibration mode. Another option is a
background calibration mode where the part continuously per-
forms self-calibration and updates the calibration coefficients.
Once the part is in this mode, the user does not have to worry
about issuing periodic calibration commands to the device or
The AD7711 gives the user access to the on-chip calibration
registers allowing the microprocessor to read the device’s cali-
bration coefficients and also to write its own calibration coeffi-
cients to the part from prestored values in E2PROM. This gives
the microprocessor much greater control over the AD7711’s
calibration procedure. It also means that the user can verify that
the device has performed its calibration correctly by comparing the
coefficients after calibration with prestored values in E2PROM.
The AD7711 can be operated in single supply systems provided
that the analog input voltage does not go more negative than
–30 mV. For larger bipolar signals, a VSS of –5 V is required by
the part. For battery operation, the AD7711 also offers a soft-
ware-programmable standby mode that reduces idle power
consumption to typically 7 mW.
THEORY OF OPERATION

The general block diagram of a sigma-delta ADC is shown in
Figure 4. It contains the following elements:A sample-hold amplifier.A differential amplifier or subtracter.An analog low-pass filter.A 1-bit A/D converter (comparator).A 1-bit DAC.A digital low-pass filter.
Figure 4.General Sigma-Delta ADC
In operation, the analog signal sample is fed to the subtracter,
along with the output of the 1-bit DAC. The filtered difference
signal is fed to the comparator, whose output samples the differ-
ence signal at a frequency many times that of the analog signal
sampling frequency (oversampling).
Oversampling is fundamental to the operation of sigma-delta
ADCs. Using the quantization noise formula for an ADC:
SNR = (6.02 · number of bits + 1.76) dB,
a 1-bit ADC or comparator yields an SNR of 7.78 dB.
The AD7711 samples the input signal at a frequency of 39 kHz or
greater (see Table III). As a result, the quantization noise is
spread over a much wider frequency than that of the band of
interest. The noise in the band of interest is reduced still further
by analog filtering in the modulator loop, which shapes the
quantization noise spectrum to move most of the noise energy to
frequencies outside the bandwidth of interest. The noise perfor-
mance is thus improved from this 1-bit level to the performance
outlined in Tables I and II and in Figure 2.
The output of the comparator provides the digital input for the
1-bit DAC, so that the system functions as a negative feedback
loop that tries to minimize the difference signal. The digital data
that represents the analog input voltage is contained in the duty
Sigma-delta ADCs are generally described by the order of the
analog low-pass filter. A simple example of a first order sigma-
delta ADC is shown in Figure 5. This contains only a first order
low-pass filter or integrator. It also illustrates the derivation of
the alternative name for these devices: Charge-Balancing ADCs.
Figure 5.Basic Charge-Balancing ADC
It consists of a differential amplifier (whose output is the differ-
ence between the analog input and the output of a 1-bit DAC),
an integrator and a comparator. The term charge-balancing,
comes from the fact that this system is a negative feedback loop
that tries to keep the net charge on the integrator capacitor at
zero, by balancing charge injected by the input voltage with
charge injected by the 1-bit DAC. When the analog input is
zero, the only contribution to the integrator output comes from
the 1-bit DAC. For the net charge on the integrator capacitor to
be zero, the DAC output must spend half its time at +FS and
half its time at –FS. Assuming ideal components, the duty cycle
of the comparator will be 50%.
When a positive analog input is applied, the output of the 1-bit
DAC must spend a larger proportion of the time at +FS, so the
duty cycle of the comparator increases. When a negative input
voltage is applied, the duty cycle decreases.
The AD7711 uses a second order sigma-delta modulator and a
digital filter that provides a rolling average of the sampled out-
put. After power-up, or if there is a step change in the input
voltage, there is a settling time that must elapse before valid
data is obtained.
Input Sample Rate

The modulator sample frequency for the device remains at
fCLK IN/512 (19.5 kHz @ fCLK IN = 10 MHz) regardless of the
selected gain. However, gains greater than ·1 are achieved by a
combination of multiple input samples per modulator cycle and
a scaling of the ratio of reference capacitor to input capacitor.
As a result of the multiple sampling, the input sample rate of
the device varies with the selected gain (see Table III). The
effective input impedance is 1/C · fS where C is the input sam-
pling capacitance and fS is the input sample rate.
Table III.Input Sampling Frequency vs. Gain
AD7711
DIGITAL FILTERING

The AD7711’s digital filter behaves like a similar analog filter,
with a few minor differences.
First, since digital filtering occurs after the A-to-D conversion
process, it can remove noise injected during the conversion
process. Analog filtering cannot do this.
On the other hand, analog filtering can remove noise super-
imposed on the analog signal before it reaches the ADC. Digital
filtering cannot do this and noise peaks riding on signals near
full scale have the potential to saturate the analog modulator
and digital filter, even though the average value of the signal is
within limits. To alleviate this problem, the AD7711 has
overrange headroom built into the sigma-delta modulator and
digital filter which allows overrange excursions of 5% above the
analog input range. If noise signals are larger than this, consid-
eration should be given to analog input filtering, or to reducing
the input channel voltage so that its full scale is half that of the
analog input channel full scale. This will provide an overrange
capability greater than 100% at the expense of reducing the
dynamic range by 1 bit (50%).
Filter Characteristics

The cutoff frequency of the digital filter is determined by the
value loaded to bits FS0 to FS11 in the control register. At the
maximum clock frequency of 10 MHz, the minimum cutoff
frequency of the filter is 2.58 Hz while the maximum program-
mable cutoff frequency is 269 Hz.
Figure 6 shows the filter frequency response for a cutoff fre-
quency of 2.62 Hz which corresponds to a first filter notch fre-
quency of 10 Hz. This is a (sinx/x)3 response (also called sinc3)
that provides >100 dB of 50 Hz and 60 Hz rejection. Program-
ming a different cutoff frequency via FS0–FS11 does not alter
the profile of the filter response; it changes the frequency of the
notches as outlined in the Control Register section.
Figure 6.Frequency Response of AD7711 Filter
Since the AD7711 contains this on-chip, low-pass filtering,
there is a settling time associated with step function inputs, and
data on the output will be invalid after a step change until the
settling time has elapsed. The settling time depends upon the
notch frequency chosen for the filter. The output data rate
equates to this filter notch frequency and the settling time of the
Post Filtering

The on-chip modulator provides samples at a 19.5 kHz output
rate. The on-chip digital filter decimates these samples to pro-
vide data at an output rate which corresponds to the pro-
grammed first notch frequency of the filter. Since the output
data rate exceeds the Nyquist criterion, the output rate for a
given bandwidth will satisfy most application requirements.
However, there may be some applications which require a
higher data rate for a given bandwidth and noise performance.
Applications which need this higher data rate will require some
post filtering following the digital filter of the AD7711.
For example, if the required bandwidth is 7.86 Hz but the re-
quired update rate is 100 Hz, the data can be taken from the
AD7711 at the 100 Hz rate giving a –3 dB bandwidth of
26.2 Hz. Post filtering can be applied to this to reduce the band-
width and output noise, to the 7.86 Hz bandwidth level, while
maintaining an output rate of 100 Hz.
Post filtering can also be used to reduce the output noise from
the device for bandwidths below 2.62 Hz. At a gain of 128, the
output rms noise is 250 nV. This is essentially device noise or
white noise, and since the input is chopped, the noise has a flat
frequency response. By reducing the bandwidth below 2.62 Hz,
the noise in the resultant passband can be reduced. A reduction
in bandwidth by a factor of two results in a √2 reduction in the
output rms noise. This additional filtering will result in a longer
settling time.
Antialias Considerations

The digital filter does not provide any rejection at integer mul-
tiples of the modulator sample frequency (n · 19.5 kHz, where
n = 1, 2, 3 . . . ). This means that there are frequency bands,f3 dB wide (f3 dB is cutoff frequency selected by FS0 to FS11)
where noise passes unattenuated to the output. However, due to
the AD7711’s high oversampling ratio, these bands occupy only
a small fraction of the spectrum and most broadband noise is
filtered. In any case, because of the high oversampling ratio a
simple, RC, single pole filter is generally sufficient to attenuate
the signals in these bands on the analog input and thus provide
adequate antialiasing filtering.
If passive components are placed in front of the AD7711, care
must be taken to ensure that the source impedance is low enough
so as not to introduce gain errors in the system. The dc input
impedance for the AD7711 is over 1 GW. The input appears as
a dynamic load which varies with the clock frequency and with
the selected gain (see Figure 7). The input sample rate, as
shown in Table III, determines the time allowed for the analog
input capacitor, CIN, to be charged. External impedances result
in a longer charge time for this capacitor and this may result
in gain errors being introduced on the analog inputs. Table IV
shows the allowable external resistance/capacitance values such
that no gain error to the 16-bit level is introduced while Table V
shows the allowable external resistance/capacitance values such
that no gain error to the 20-bit level is introduced. Both inputs
of the differential input channel (AIN1) look into similar input
circuitry.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED