74HC4016PW ,74HC/HCT4016; Quad bilateral switchesINTEGRATED CIRCUITSDATA SHEETFor a complete data sheet, please also download:• The IC06 74HC/HCT/HC ..
74HC4017D ,Johnson decade counter with 10 decoded outputsGeneral descriptionThe 74HC4017; 74HCT4017 is a 5-stage Johnson decade counter with 10 decoded outp ..
74HC4017N ,74HC/HCT4017; Johnson decade counter with 10 decoded outputsGENERAL DESCRIPTIONtable).The 74HC/HCT4017 are high-speed Si-gate CMOSWhen cascading counters, the ..
74HC4017PW ,74HC/HCT4017; Johnson decade counter with 10 decoded outputsFeatures and benefits Wide supply voltage range from 2.0 V to 6.0 V Input levels: For 74HC4017: ..
74HC4020 ,14-stage binary ripple counter
74HC4020 ,14-stage binary ripple counter
74LVT16245BDGGRE4 ,3.3-V ABT 16-Bit Bus Transceivers With 3-State Outputs 48-TSSOP -40 to 85/sc/package.Please be aware that an important notice concerning availability, standard warranty, an ..
74LVT16245MEA ,Low Voltage 16-Bit Transceiver with 3-STATE Outputs74LVT16245 • 74LVTH16245 Low Voltage 16-Bit Transceiver with 3-STATE OutputsJanuary 1999Revised Aug ..
74LVT16245MEAX ,Low Voltage 16-Bit Transceiver with 3-STATE OutputsFeaturesThe LVT16245 and LVTH16245 contain sixteen non-invert-
74HC4016D-74HC4016N-74HC4016PW
74HC/HCT4016; Quad bilateral switches
Philips Semiconductors Product specification
Quad bilateral switches 74HC/HCT4016
FEATURES Low “ON” resistance:
160Ω (typ.) at VCC= 4.5 V
120Ω (typ.) at VCC= 6.0 V Ω (typ.) at VCC= 9.0 V Individual switch controls Typical “break before make” built in Output capability: non-standard ICC category: SSI
GENERAL DESCRIPTIONThe 74HC/HCT4016 are high-speed Si-gate CMOS
devices and are pin compatible with the “4016” of the
“4000B” series. They are specified in compliance with
JEDEC standard no. 7A.
The 74HC/HCT4016 have four independent analog
switches (transmission gates).
Each switch has two input/output terminals (Yn,Zn) and an
active HIGH enable input (En). When En is connected to
VCC, a low bidirectional path between Yn and Znis
established (ON condition). When En is connected to
ground (GND), the switch is disabled and a high
impedance between Yn and Zn is established (OFF
condition).
Current through a switch will not cause additional
VCC current provided the voltage at the terminals of the
switch is maintained within the supply voltage range;
VCC >> (VY,VZ) >> GND. Inputs Yn and Zn are electrically
equivalent terminals.
QUICK REFERENCE DATAGND = 0 V; Tamb = 25 °C; tr = tf = 6 ns
Notes CPD is used to determine the dynamic power dissipation (PDin μW): = CPD× VCC2×fi +∑ {(CL+ CS)× VCC2×fo} where: = input frequency in MHz = output frequency in MHz {(CL+ CS)× VCC2×fo} = sum of outputs= output load capacitance in pF= max. switch capacitance in pF
VCC= supply voltage in V For HC the condition is VI = GND to VCC
For HCT the condition is VI = GND to VCC− 1.5 V
ORDERING INFORMATIONSee “74HC/HCT/HCU/HCMOS Logic Package Information”.
Philips Semiconductors Product specification
Quad bilateral switches 74HC/HCT4016
PIN DESCRIPTION
Philips Semiconductors Product specification
Quad bilateral switches 74HC/HCT4016
FUNCTION TABLE
Notes H = HIGH voltage level = LOW voltage level
APPLICATIONS Signal gating Modulation Demodulation Chopper
Philips Semiconductors Product specification
Quad bilateral switches 74HC/HCT4016
RATINGSLimiting values in accordance with the Absolute Maximum System (IEC 134)
Voltages are referenced to GND (ground = 0 V)
RECOMMENDED OPERATING CONDITIONS
Philips Semiconductors Product specification
Quad bilateral switches 74HC/HCT4016
DC CHARACTERISTICS FOR 74HC/HCTFor 74HC: VCC= 2.0, 4.5, 6.0 and 9.0 V
For 74HCT: VCC= 4.5 V
Notes to the DC Characteristics At supply voltages approaching 2.0 V the analog switch ON-resistance becomes extremely non-linear. Therefore it
is recommended that these devices be used to transmit digital signals only, when using these supply voltages. For test circuit measuring RON see Fig.6.
Philips Semiconductors Product specification
Quad bilateral switches 74HC/HCT4016
